1. Manuals
  2. Brands
  3. Triangle MicroSystems Manuals
  4. Control Systems
  5. PETROSMART EZ
  6. Installation instructions manual

Triangle MicroSystems PETROSMART EZ Installation Instructions Manual

Instructions for connecting petrosmart ez control systems to bennett 3k series electronic dispensers without credit card modules
Hide thumbs Also See for PETROSMART EZ:
Table of Contents

Advertisement

Quick Links

See also: Instruction and Installation Manual
Installation Instructions
Instructions for Connecting
PETROSMART EZ Control Systems
to
Bennett 3K series Electronic Dispensers
Without CREDIT CARD MODULES
Read This Book
This book has important information for safe installation and operation of this equipment. Read and understand this
book before applying power. Keep this book and tell all service personnel to read this book. If you do not follow the
instructions, you can cause damage to the equipment, injury, or death.
Triangle MicroSystems Inc.
2716 Discovery Drive
Raleigh, N.C. 27616
(919) 878-1880
http://www.trianglemicrosystems.net
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PETROSMART EZ and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Triangle MicroSystems PETROSMART EZ

Summary of Contents for Triangle MicroSystems PETROSMART EZ

  • Page 1 Installation Instructions Instructions for Connecting PETROSMART EZ Control Systems Bennett 3K series Electronic Dispensers Without CREDIT CARD MODULES Read This Book This book has important information for safe installation and operation of this equipment. Read and understand this book before applying power. Keep this book and tell all service personnel to read this book. If you do not follow the instructions, you can cause damage to the equipment, injury, or death.

  • Page 2: Table Of Contents

    PetroSmart EZ Control System Table of Contents SECTION Page Dangers Warnings and Precautions System Requirements System Description PetroSmart EZ System Diagram Bennett Dispenser Control Interconnect Box Connection of Dispenser Control Data Wires PetroSmart EZ Converter Board Power Requirements Cable Connections...

  • Page 3: Dangers Warnings And Precautions

    Dangers, Warnings and Precautions FOR THE SAFE INSTALLATION, MAINTENANCE, AND OPERATION OF THIS CONSOLE AND RELATED EQUIPMENT, READ AND UNDERSTAND ALL WARNINGS AND CAUTIONS. "DANGER": means: If you do not follow the instructions, severe injury or death will occur. “WARNING": means: If you do not follow the instructions, severe injury or death can occur.

  • Page 4: System Requirements

    System Requirements In developing the Triangle MicroSystems control system for Bennett dispensers, Bennett provided the communication protocols that required separate data wires for each dispenser. This is Bennett standard policy for “third party” control systems. Secondly, the TMS control system does not require the Bennett interface box to interface with the dispensers.

  • Page 5: System Description

    PETROSMART EZ System Description The PETROSMART EZ fuel control system for BENNETT electronics was designed to control 3K series electronic dispensers without credit card modules. The PETROSMART EZ dispenser control system is comprised of the following items: Qty. Description PETROSMART EZ Console.

  • Page 6: Petrosmart Ez System Diagram Pg

    Fueling Positions The maximum number of fueling positions permissible is 8 for a PETROSMART EZ-8 or 16 for a PETROSMART EZ-16, where each side of an MPD (no matter how many grades) counts as one fueling position. PetroSmart EZ System Diagram...

  • Page 7: Bennett Dispenser Control Interconnect Box

    PILOT DUTY ONLY (1A @ 115 VAC MAX.) Fig. 4, The PetroSmart EZ Bennett Dispenser Control Box with the Door Open. NOTE: This figure shows INCORRECT CABLE CONNECTION between the front and back pan. Figure 3 shows correct connection after the IC Box has been closed.

  • Page 8: Connection Of Dispenser Control Data Wires

    The EZ TM85 communication board/power supply receives the incoming line voltage (120 VAC), supplies the operating system with DC voltage. The dispenser IC box transmits data signals between the console and the dispenser. Connection of Dispenser Control, Data Wires 115 VAC From Credit Card Dispenser Control Data Wires Dispenser Modules...

  • Page 9: Petrosmart Ez Converter Board

    CONN2 CONN3 Fig. 6, PETROSMART EZ Converter Board The converter board is located on the inside cover of both the dispenser control IC box; refer to Figure 4 on page IMPORTANT After installation of IC box, check the slide switch on the converter board (Refer to Fig. 10) for the proper switch position.

  • Page 10: Power Requirements

    (min.), and in conduit. Do not put wiring from other sources in this conduit. 3. PETROSMART EZ Console: a standard plug-in AC Adaptor power module powers the console. The Adaptor can be inserted into a standard electrical outlet that supplies, 115VAC, 60Hz, and 15W power. The Adaptor converts the input to 15 VDC, 600mA that it supplies to the EZ console.

  • Page 11: Cable Connections

    A connection is made between the IC Box back pan to the front pan is made via a 3 foot round cable having 15- conductors and DB-15 type connectors to the right most connection labeled “3” or the right most connection when the door is closed. Refer to the PetroSmart EZ console, programming/operators guide on how to program the console.

  • Page 12: Important Notes

    4. Use cable ties to keep the data cable in place from the console to the interconnect box if conduit is not used. 5. If the PETROSMART EZ cable is put through a conduit, use 2" minimum to allow room for the connectors on the cable.

  • Page 13: Specifications

    PERIPHERAL INTERFACE INSTALLATION In compliance with the UL regulations and standards that apply to the Petroleum Industry, the following information establishes installation parameters for the use of peripheral equipment with the PETROSMART EZ Control Console. 1. Any peripheral equipment must be UL listed.

  • Page 14: Tms Service And Warranty Information

    WARRANTY AND SERVICE INFORMATION WARRANTY AND LIMITATIONS OF REMEDIES TMS warrants that new equipment manufactured by TMS shall be free of defective parts and workmanship for a period of two (2) years, commencing on the day of invoice from TMS. TMS salesmen, distributors, representatives, or agents may have made oral statements about the equipment described herein.
  • Page 15 WARRANTY REPAIR POLICY During the warranty period, defective TMS components may be returned freight-prepaid to Triangle MicroSystems, Inc. TMS will repair or replace, solely at our discretion, at no charge, and return via ground shipment freight-prepaid, such components that are judged to be defective in materials or workmanship. Please note that a repair under warranty does not extend or renew the original warranty period.

Table of Contents