Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Klein Blackbox+ series
- Page 2 Thank You We appreciate you purchasing Blackbox™ two-way radios. We believe that the quality and function of this product is the best available today. Cost-effective portable + Series radios are the result of Blackbox’s pursuing high quality and high performance, ergonomic design, reliable quality and stable performance.
- Page 3 Safety Please switch off the radio before entering a potentially explosive or flammable environment. Do not change or charge battery pack in a potentially explosive or flammable environment. Do not use damaged antenna. Damaged antenna may cause burns. Do not disassemble the radio. Do not put the radio within the possible range of an air bag in a car.
- Page 4 Unpack and Check Before use, we recommend that you check the packing and identify the items listed below. If any damages have occurred during shipment, please contact your local dealer. Items Radio Antenna Battery Belt Clip Charger w/adaptor Quantity 1 Note: For frequency band of antenna, please refer to the label on the bottom of the antenna.
- Page 5 Warning: Please prevent the battery electrode from contacting with any metal conductors such as jewels or keys. Charging Steps: Please charge as follows: 1. Connect the adapter with the charger. 2. Plug the adapter into an AC outlet. 3. The charger is ready for charging if the indicator lights red for one second and goes off.
- Page 6 Installing and removing Installing/Detaching the Battery Installing the Battery Match the guides of the battery pack with the corresponding grooves at the bottom of radio and insert the battery pack. Then press downward battery pack until the release latch locks. Removing of Battery: Before removing, make sure that the radio is switched off.
- Page 7 Installing/Removing Belt Clip Installing Belt Clip ( Picture III) Picture III Picture IV Match the grooves of belt clip with those on the rear of radio and press the belt clip downwards until it is locked. Removing Belt Clip (Picture IV) Use your nail or a tool to lift the metal spring piece in the belt clip from topside and pull the belt clip upward from the battery pack.
- Page 8 Over View Antenna ‚The Indicator The indicator lights red when transmitting; lights green when receiving; flashes red when the battery power is low; flashes green when scanning. ƒ Power/Volume Switch Turn it clockwise to switch on the radio until a click is felt. Rotate it to adjust volume after turn on the radio. Turn it counter clockwise to switch off the radio until a click is felt.
- Page 9 Over View (continued) ŠStrap Hole To be used with hand strap. Programmable key The press mode and its function can be programmed by PC software. Note: The press duration and corresponding function The original default setting: Short Press (0.5s): Monitor Long Press (1.5s): Announce Battery Power www.blackboxradios.com...
-
Page 10: Switch On/Off
Basic Operation Switch ON/OFF Switch on the radio by turning the Power/Volume switch clockwise until a click is felt. At the same time, a voice indication of the current channel is heard. To switch off the radio, turn the Power/Volume switch counter clockwise until a click is felt. Volume Adjustment Rotate the Power/Volume switch to adjust volume when the radio is turned on. -
Page 11: Auxiliary Functions
Auxiliary Functions PC Programming 1. Visit blackboxradios.com to download standard software. 2. Turn off the radio and connect it and PC with programming cable. 3. Install and run the software. Then turn on the radio. Use the software to set parameters of the radio. - Page 12 Optional programming: Monitor To turn on signaling squelch, press programmed key with a “beep” sound. Press the key again to quit with two “beeps”. This is to monitor signals that are inaudible due to the CTCSS/CDCSS squelch. Monitor Momentary (only can be set as long key or normal key) Press and hold the programmed key to turn on signal squelch.
- Page 13 Scan The scan function should be preset by the PC programming. (The default setting of S channel is normal operating channel.) 1. Rotate the channel knob to the S channel and the radio begins scanning. The indicator flashes green during scanning.
-
Page 14: Wired Clone
Wired Clone 1. Connect host radio and sub radio with Clone Cable. Make sure that the radios are turned off. 2. Press and hold programmed key on host radio, then turn on the host radio. The indicator flashes red twice, which means the host radio is ready for cloning. -
Page 15: Specification
Specification General Frequency Range VHF: 136~174MHz UHF:430-470MHz: 400-440MHz: 470-512MHz Channel Capacity 16 (15+S) Channel Spacing 25.0kHz / 12.5kHz Frequency Stability ±2.5PPM Operating Temperature -25~+55°C Antenna Impendence 50Ω Operating Voltage 7.4V Dimension (W×H×D) 2.165” × 4.37” × 1.26” Weight (with antenna & battery) 232g Battery 1300mAh(Li-ion Battery) Transmitter:... - Page 16 Warranty and Return Policy 2008 / 2009 Defects in material or workmanship under normal use and service, items will be repaired or replaced free of charge from 1 Year from date code on product. Simply contact your salesperson for repair or replacement. Blackbox Radios warrants all products against manufacturer’s defects as long as the product is still under warranty.
- Page 18 ©2009 Blackbox Radios ® Names and logos used are the property of their respective owners...