Table of Contents
Advertisement
Quick Links
To ensure correct operation and service please read these instructions before installing and
operating the TPMS
1. Notice.......................................................................................1
2. W401A Tire Pressure Monitoring System........................................2
3. W401A Tire Pressure Monitoring System Specification..................2
4. W401A Tire Pressure Monitoring system Accessories.....................3
5. W 4 0 1 A S y s t e m I n s ta l l a t i o n ... ... ... ... ... ... ... ... ... ... ... ... ... ... 3
Display Unit Installation.........................................................3
Wireless Transmitter Sensor Installation.......................................4
6. W401 A System Operation..........................................................6
Description for Display...............................................................6
Description for Change Mode Method.............................................7
Change Factory Default Set Up......................................................7
1. Front Tire-Low Tire Pressure Setting Mode..............................7
2. Rear Tire-Low Tire Pressure Setting Mode..............................8
3. Tire Pressure Temperature-High Tire Pressure Setting Mode......9
4. Initial Display Mode Set Up.................................................10
7. W401A Waring System Description...............................................11
8. W401A Reset for Tire Change and Rotation...................................13
Mode1：Front and Rear Tire Parallel Exchange..................................13
Mode 2：Tire Diagonal Exchange....................................................13
Mode 3：Front Tire exchange，Rear Tire Parallel change to front...........14
Mode 4：Random Reposition..........................................................14
Mode 5 ： Single Tire Sensor Replace.................................................16
9. Warranty Policy.........................................................................18
10. APPENDIX...............................................................................18
ORO
TPMS
Manual
TABLE of CONTENTS
Advertisement
Table of Contents
Related Manuals for ORO W401A
Summary of Contents for ORO W401A
-
Page 1: Table Of Contents
3. Tire Pressure Temperature-High Tire Pressure Setting Mode……9 4. Initial Display Mode Set Up……………………………….....10 7. W401A Waring System Description………………………………………..11 8. W401A Reset for Tire Change and Rotation……………………………..13 Mode1：Front and Rear Tire Parallel Exchange……………………..……..13 Mode 2：Tire Diagonal Exchange………………………………………..…..13 Mode 3：Front Tire exchange，Rear Tire Parallel change to front………..14 Mode 4：Random Reposition…………………………………………..……..14... -
Page 2: Notice
NOTICE FCC & E-Mark Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. -
Page 3: W401A Tire Pressure Monitoring System
W401A Tire Pressure Monitoring System ORO-W401A Tire Pressure Monitoring Systems (TPMS), can monitor and provide tire pressure, tire temperature and car battery information by real time to help the driver to control and keep the normal tire pressure in order to reduce the fuel consumption and extend the tire life, and also through the battery information, the driver can change the battery before happens any bug and reduce the % of vehicle breakdown on the road. - Page 4 1.9 ~ 2.8 bar (27 ~ 40 psi; 190 ~ 280 kPa)，the factory Cold-Tire Std. Tire pressure setting range default is.3bar (32psi; 230kPa) 60℃~99℃(140℉~212℉)，the factory default is 80 ℃ Tire Temperature Warning Range (176℉) W401A TPMS Accessories Accessories Pictures QTY Accessories Picture Nylok Screw...
-
Page 5: Display Unit Installation
W401A TPMS INSTALLATION 1. Display Installation: Firm the magnetic holder in the suitable place. (Suggest place , as shows in the picture) b. Plug in the USB cigarette power cable on the back of display. Put the display on the magnetic holder. - Page 6 Take off the tire and bleed the air, then should change to the ORO-TEK TPMS valve, and follow the steps: 1. Snap in the valve from the internal edge side of the wheel. 2. Adjust the valve’s angle, and make the valve be vertical by the edge of the wheel.
- Page 7 Put the marked No. 1 tire sensor to the tire which market No. 1. as step a. photo and follow steps: 1. Install the tire sensor to the valve. 2. Use the nylok screw and tight up with the tire sensor. (Pls.
-
Page 8: W401 A System Operation
ORO-W401A includes bar, kPa, psi which are 3 kinds of pressure’s unit and ℃、℉ for temperature unit for user, the factory default for pressure unit is bar, the user can change the pressure unit by for 2 sec., and the factory default for temperature is ℃, the user can... -
Page 9: Front Tire-Low Tire Pressure Setting Mode
1psi (7kPa) when the temperature got difference of 10℉ (6℃), and this is normal physics phenomenon. ORO TEK suggest to the user , when is checking on tire pressure, it’s important to keep the tire pressure under suitable pressure, the Low tire pressure unit will be recognized as warning unit, however, when the pressure is higher than 25% from the cold tire unit, the system will start the alarming. -
Page 10: Rear Tire-Low Tire Pressure Setting Mode
system will automatically enter the Rear tire Low pressure set up mode. Rear Tire-Low Tire Pressure Setting Mode Setp Operating Process Photograph The system will enter the Rear Tire low pressure set up mode automatically after set up the Front Tire Low Pressure set up mode. - Page 11 The display shows on the figure is the tires factory default high temperature value (80 C) for the tires in blue. If there is no modification to the user, then press the Set Up button to enter the next set up mode. NOTE: If the unit is ℉...
- Page 12 Set Up button, the system will complete the Power On mode the back to the normal operation mode to monitoring tire pressure/temperature and battery voltage. W401A System Alarm Mode Description Mode Warning Condition and Warning Method Display Figure Warning Situation: When the tire pressure >...
- Page 13 warning when the tire figure displayed in RED. Warning Situation: When the temperature is higher than set up unit. (Factory default is 80℃ and 176℉ Warning Method: Will sound Beep Beep as warning when the tire figure displayed in RED. Warning Situation: When the tire pressure is deflating rapidly.
- Page 14 W401 Reset for Tire Changing and Rotation When the user are doing/finished the changing or rotating the tires, should also reset the monitors ID’s position, however, ORO TEK TPMS provides 4 modes in order to make the user can reset rapidly and keep the tire position as same as shows by the monitor.
-
Page 15: Mode 2：Tire Diagonal Exchange
Description for each set up process Mode 1: Front and Rear tire exchange FRONT No. 4 No. 1 No. 3 No. 2 The monitor will show up as below photograph, the NO. 1 which shows in yellow means the mode 1, and the 4 red lights means the tire position before reset as shows in pic. -
Page 16: Mode 4：Random Reposition
Pic. 1 Pic. 2 模式 3：Front Tire Diagonal exchange, Rear Tire parallel change to the front FRONT No 4 No 1 No 3 No 2 The monitor will show up as below photograph (Pic. 1 and Pic 2), the No. 3 in yellow means in mode 3. and the 4 red lights means the tire position before reset as shows in pic. - Page 17 1. Set up for RF tire sensor: The display will flash green and red with No. 1 which means the RF tire can be proceed for the set up as below pic. 1, by the meantime the user should deflate the tire pressure rapidly over than 0.3bar/30kPa or 4 Psi in 15 sec.
- Page 18 Pic 1 Pic 2 4. Set up for LF tire sensor The display will flash green and red in tire figure and No. 4 which means the LF tire can be proceed for the set up as below pic. 1, by the meantime the user should deflate the tire pressure rapidly over than 0.3bar/30kPa or 4 Psi in 15 sec.
- Page 19 Pic 1 Pic 2 2. Set up for RR tire sensor The display will flash green and red in tire figure and No. 2 which means the RR tire can be proceed for the set up as below pic. 1, by the meantime the user should deflate the tire pressure rapidly over than 0.3bar/30kPa or 4 Psi in 15 sec.
-
Page 20: Warranty Policy
The user should confirm whether the all sensors are manufactured by ORO TEK before do any changing or replacement,, if not, the user won’t be able be succeed on set up neither make the system operating normally. - Page 21 3. The user did not follow the user manual instruction on installation, incorrect installation, or bad keeping to make the systems become failure or damaged. 4. The system has been installed by non-authorized distributor or technician from ORO-TEK. 5. When the user is not using the original manufacturer’s accessories (ex: Power code) and make the system become failure, this are NOT included ORO-TEK warranty policy.
- Page 22 Annex II ℃ To ℉ and ℉ To ℃ Conversion Table ℃ ℉ ℃ ℉ ℃ ℉...
Need help?
Do you have a question about the W401A and is the answer not in the manual?
Questions and answers