Antunes WD-20 Series Owner's Manual

Without water tray
Hide thumbs Also See for WD-20 Series:

Advertisement

WD-20 Shown
WD-20, WD-21A, WD-35A
Warmer Drawer (without water tray)
owner's manual
Manufacturing Numbers:
9400130, 9400132, 9400133, 9400134, 9400136,
9400140, 9400142, 9400144, 9100145, 9400146,
9400150, 9400152, 9400154, 9100155, 9400156
C
US
C
US
CM
www.antunes.com
P/N 1010889 Rev. B 09/16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WD-20 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Antunes WD-20 Series

  • Page 1 WD-20 Shown WD-20, WD-21A, WD-35A Warmer Drawer (without water tray) owner’s manual Manufacturing Numbers: 9400130, 9400132, 9400133, 9400134, 9400136, 9400140, 9400142, 9400144, 9100145, 9400146, 9400150, 9400152, 9400154, 9100155, 9400156 www.antunes.com P/N 1010889 Rev. B 09/16...
  • Page 2: Table Of Contents

    WARMER DRAWER TABLE OF CONTENTS Equipment Setup ............6 Owner Information .............2 Operation ..............7 General ..............2 Operating Instructions ..........7 Warranty Information ..........2 Hi-Limit Reset ............7 Service/Technical Assistance ........3 Maintenance ..............8 Important Safety Information ........3 Cleaning ..............8 Specifications .............5 Replacing Components ..........8 Electrical Ratings ............5 Troubleshooting ............9 Capacity ..............5...
  • Page 3: Service/Technical Assistance

    WARMER DRAWER OWNER INFORMATION (continued) Service/Technical Assistance If you experience any problems with the installation or operation of your unit, contact Antunes Technical Service. Fill in the information below and have it handy when calling Antunes Technical Service for assistance. The serial number is on the specification plate located on the unit.
  • Page 4 WARMER DRAWER IMPORTANT SAFETY INFORMATION (continued) In addition to the warnings and cautions in this manual, • The procedures in this chapter may include use the following guidelines for safe operation of the the use of chemical products. These chemi- cal products will be highlighted with bold unit.
  • Page 5: Specifications

    WARMER DRAWER SPECIFICATIONS Electrical Ratings Electrical Cord & Plug Configurations Model & Mfg. No Volts Watts Amps Hertz Letter Description Configuration Code* WD-20-CF 50/60 9400130 Harmonized Cord WD-20-HC 50/60 9400132 WD-20-CF 50/60 (H)C** CEE 7/7 16 Amp, 250 9400134 VAC (Assembly Only) WD-20 HG 50/60 (C)F***...
  • Page 6: Installation

    NOTE: Do not use a dripping wet cloth. Wring out before use. 4. Install parts into unit. NOTE: If any parts are missing or damaged, con- Drawer tact A.J. Antunes & Co. IMMEDIATELY at 1-877-392- 7854. Figure 1. Warmer Drawer–WD-20 Equipment Setup Trivet When placing the unit into service, pay attention to the following guidelines.
  • Page 7: Operation

    WARMER DRAWER OPERATION Operating Instructions The recommended starting temperature for hot dog THERMOSTAT buns and hard rolls is 140°F (60°C). Your opera- HEATER tion may require temperature adjustment up or down, POWER depending on product and usage. Most products warm to serving temperature of 130°- 140°F (54°- 60°C) in 15-20 minutes and remain ready to serve for up to 1½...
  • Page 8: Maintenance

    WARMER DRAWER MAINTENANCE 3. Wipe the exterior of unit with a damp cloth or WARNING stainless steel cleaner, then wipe dry with a clean, Turn the unit off, disconnect the power source and dry cloth. allow the unit to cool down before performing any ser- 4.
  • Page 9: Troubleshooting

    WARMER DRAWER TROUBLESHOOTING WARNING To avoid possible personal injury and/or damage to the unit, inspection, test and repair of electrical equipment should be performed by qualified service personnel. The unit should be unplugged when servicing. Problem Possible Cause) Corrective Action Unit will not heat up.
  • Page 10: Wiring Diagram

    WARMER DRAWER WIRING DIAGRAM POWER CORD NOTE: ALL WIRES TO BE 16 GA. TFE-200°C UNLESS OTHERWISE SPECIFIED. HI-LIMIT THERMOSTAT TERMINAL BLOCK POWER SWITCH INDICATOR HEATER LIGHT ELEMENT THERMOSTAT P/N 1010889 Rev. B 09/16...
  • Page 11: Replacement Parts - Wd-20

    WARMER DRAWER REPLACEMENT PARTS – WD-20 17 31 P/N 1010889 Rev. B 09/16...
  • Page 12 WARMER DRAWER REPLACEMENT PARTS – WD-20 (continued) Item Part Description Qty. Item Part Description Qty. 0010439 Housing, Outer 4060323 Indicator Light, Heater ON, 0021345 Liner Weldment, Inner 120 Volt 0502937 Base Plate 4060229 Indicator Light, Heater ON, 0504278 Control Panel 230 Volt 210K230 Bumper Leg Kit...
  • Page 13: Replacement Parts - Wd-21A & 35A

    WARMER DRAWER REPLACEMENT PARTS – WD-21A & 35A P/N 1010889 Rev. B 09/16...
  • Page 14 WARMER DRAWER REPLACEMENT PARTS – WD-21A & 35A (continued) Item Part Description Qty. Item Part Description Qty. 0501894 Cover (WD-21A) 4060323 Indicator Light, Heater ON, 0501199 Cover (WD-35A) 120 Volt 0021347 Liner Weldment, Inner (WD-21A) 1 4060229 Indicator Light, Heater ON, 0021350 Liner Weldment, Inner (WD-35A) 1 230 Volt...
  • Page 15: Notes

    WARMER DRAWER NOTES P/N 1010889 Rev. B 09/16...
  • Page 16: Limited Warranty

    Limited Warranty Equipment manufactured by Roundup Food Equipment Division of A.J. Antunes & Co. has been constructed of the finest materials available and manufactured to high quality standards. These units are warranted to be free from mechanical and electrical defects for a period of one year from date of purchase or 18 months from shipment from factory, whichever occurs first, under normal use and service, and when installed in accordance with manufacturer’s recommendations.

Table of Contents