Download Print this page

Resolution Products Wireless Translator RE208 Instructions

Hardwire-to-honeywell

Advertisement

Quick Links

Wireless
Security
Solutions
®
RE208 Hardwire-to-Honeywell
Wireless Translator™
Features
• Converts hardwire zones into Honeywell-compatible wireless signals.
• 8 Hardwire loops with end-of-line resistor detection.
• Unique wireless ID for each zone, plus 1 for main device.
• Transmit diversity for long reliable range.
• PIR powering (via external supply).
• 3 year operation on batteries (contacts only).
• Complete supervision of zone tampers and low battery.
Key Instructions
• Use with normally closed contacts in-line with 4.7 K-ohms end-of-line resistors.
• Not for use with life safety devices, such as Smoke or CO sensors.
• External supply requirements (wall-AC): 12V DC at least 50 mA.
• PIR & Glassbreak (powered devices) usage:
4-wire devices only. Not for use with 2-wire powered devices.
2 AA back-up batteries will drive contacts only, and cannot drive a PIR.
Under external supply failure, the PIR/Glass would likely alarm.
If using PIR/Glass, we recommend using 12V DC, 24-hour back-up supply.
If using old panel 12V DC supply, verify operation and old battery.
• Enrolling:
Hardwire zones (labeled "Loops" on the circuit board terminals):
• Hardwire zones are enrolled into Honeywell system using the RF Learning
tripping enrollment mode.
• Input Type: 3 (Supervised RF), Loop: 2
• When prompted, open/close each zone twice
(fault/restore/fault/restore) to enroll the serial number.
Translator itself. Trouble supervision of the Translator itself is recommended;
Assign the Translator to a zone for sending check-in supervisories, cover
tamper and low battery.
• Zone Type: 8 (24 hour Aux) – When cover opened: "fault" when system
not armed, "alarm" when armed.
• Input Type: 3 (Supervised RF), Loop: 4
• When prompted, toggle the tamper switch to enroll the serial number.
Operation
• 8 Hardwire 4.7K-ohm Zones – transmit 8 unique wireless IDs:
Alarm on open circuit. Tamper on short circuit.
Supervisories, every hour for each zone.
RE208_Hardwire_to_Honeywell-Compat_Translator.doc
Page 1 of 4
www.ResolutionProducts.com
5/25/2011
• Translator Main Zone wireless transmission (9
Tamper, when cover opened.
Low battery, when either low AA batteries, OR loss of 12V DC external.
Supervisory every hour.
• How ID's work: If the Translator Main Zone is XXX-YYY0, then the Zone 1's ID is
XXX-YYY1, and Zone 2's ID is XXX-YYY2, etc.
• LED Operation
Green LED: On if AC power present.
Red LED:
When 12V DC is present: "Blinks" on transmit to panel;
"on" if device tamper or device low battery.
• Application Diagram
Existing Hardwire Sensors
Old Hardwire Panel Mounted
• Connection Diagram
Contact
Closed Normally
Open in Alarm
4.7K
To Enroll zone,
perform 2 open/close
sequences
RE208_Hardwire_to_Honeywell-Compat_Translator.doc
Page 2 of 4
www.ResolutionProducts.com
th
unique ID):
New System's wireless
language
New Wireless
System
New
Self-Contained System in
public area
in utility area
AA Backup
batteries will NOT
power PIR
PIR
12V DC
Loop
x
5/25/2011

Advertisement

loading
Need help?

Need help?

Do you have a question about the Wireless Translator RE208 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Resolution Products Wireless Translator RE208

  • Page 1 Wireless • Translator Main Zone wireless transmission (9 unique ID): Security Tamper, when cover opened. Solutions Low battery, when either low AA batteries, OR loss of 12V DC external. Supervisory every hour. ® RE208 Hardwire-to-Honeywell Wireless Translator™ • How ID’s work: If the Translator Main Zone is XXX-YYY0, then the Zone 1’s ID is XXX-YYY1, and Zone 2’s ID is XXX-YYY2, etc.
  • Page 2 Talks to SAW receivers. Zone sensing duration: State sensed if held more than 600ms. Resolution Products, Inc. products will function with one of either GE, DSC or Honeywell systems. End-of-line Resistors: 4.7k-ohm, 5%. However, no Resolution product is produced by, endorsed by, nor is officially associated with GE, Honeywell or DSC.