Related Manuals for CNC Router Parts CRP600 Benchtop PRO
Summary of Contents for CNC Router Parts CRP600 Benchtop PRO
- Page 1 CRP600 Benchtop PRO CNC Machine Assembly Instructions Updated 10/26/2015 SHEET 1 of 14...
-
Page 2: Step 1: Leg Assembly
Step 1: Leg Assembly Parts Added Front Back PART 4080 Extrusion x 160 mm TNR-M8, Roll in M8 T-nut 7002, Leveling Foot End Plate BHCP-M8-16, M8 Button Head Cap Screw x 16mm 6036, 40mm Single Gusset 7036, M12 Leveling Foot, 50mm Fasteners in bag: CRP613-00-FAST Assemble the leg pieces by attaching the feet to the ends of the extrusion and attaching the 40mm gussets to the other end. - Page 3 Step 2: X-axis Crossmembers Parts Added X' Axis PART CRP610 Ballscrew X-Axis Front BHCP-M8-30, M8 Button Head Cap Screw x 30mm TNR-M8, Roll in M8 T-nut 2002, Anchor Fastener 6.3in 4080 Extrusion x 641 mm 160mm V-Con Wiper Fasteners in bag: CRP610-00-FAST A) Use the anchor fasteners to attach the crossmembers to the bottom T-slot of the X-axes.
-
Page 4: Step 3: Leg Installation
Step 3: Leg installation Parts Added PART CRP610-01-00 Leg Assembly Front TNR-M8, Roll in M8 T-nut BHCP-M8-16, M8 Button Head Cap Screw x 16mm Fasteners in bag: CRP613-00-FAST Attach the legs built in step one to the table. It may be easier to install the legs with the machine flipped upside down. -
Page 5: Step 4: Riser Installation
Step 4: Riser installation Parts Added PART CRP620-02 Riser Plate SK-M8-16, M8 Socket Head Cap Screw x 16mm TNR-M8, Roll in M8 T-nut Fasteners in bag: CRP620-00-FAST Attach the riser plate to the X-axes. Front Losely attached the t-nuts and the remaining screws to the upper clearance holes on the riser plates. - Page 6 Step 5: Gantry Support Assy. Parts Added: PART TNR-M8, Roll in M8 T-nut SK-M8-16 - M8 x 16mm Socket Head Cap Screw CRP630-01 - Benchtop Pro Gantry Back Plate BHCS-M8-20 - M8 X 20mm Button Head Cap Screw 5 4080-200-BTPRO - 200mm 4080 Extrusion w/ 2xM8 Holes Fasteners in bag: CRP620-00-FAST Atach the extrusion segments to the gantry back plate.
- Page 7 Step 6: Gantry Support Install Align the riser plates by either pushing them along the axis, or by manually turning the top of the ballscrew. Then, slide the back plate and extrusion onto the untighted fasteners on the risers. Keep the top of the extrusion flush with the top of th riser plate and tighten the remaining riser fasteners.
- Page 8 Step 7: Gantry Installation Y Axis / Gantry Parts Added: PART CRP630-00 - Ballscrew Y Axis Slide the gantry onto the t-nuts in the support plate, starting at the end of the gantry opposite the motor mount. Position the gantry so that it is positioned as shown in the detail below.
- Page 9 Step 8: Z-Axis Parts Used PART CRP640 Ballscrew Z Axis SK-M6-12, M6 Socket Head Cap Screw x 12mm Fasteners in bag: CRP440-00-FAST Attach the Z-Axis assembly to the gantry interface plate with the provided screws. Back Tapped holes used on the interface plate to attach the Z- axis are indicated below with centermarks.
- Page 10 Step 9: Machine Table Extrusion Parts Added: PART TNR-M8, Roll in M8 T-nut FH-M8-30, Flat Head Socket Screw M8 x 30 CRP20160, T-Slot Machine Table Extrusion Fasteners in bag: CRP611-00-FAST 1)Roll t-nuts into cross member extrusion and position as shown. A small hex key or screwdriver simplifies this step. 2)Lay the table extrusion on the crossmembers.
-
Page 11: Step 10: Motor Installation
Step 10: Motor Installation Note: Motor kits are sold separately from the base BenchtopPRO package Depending on how your order was placed and processed, the oldham coupler may be partially or entirely installed on the ballscrew. These steps will need to be performed for all 4 axes. Coupler Installation: If the entire coupler is installed on the ballscrew: SK-M5-12... -
Page 12: Step 11: Homing Switches
Step 11: Homing Switches Note: Homing switch kits are sold separately from the base BenchtopPRO package These steps will need to be performed for the X, X' and Y axes. For both the X and X' axis, the sensor should be installed in the lower hole, as to not interfere with the riser plate. - Page 13 Step 12: Cable Track Support Parts Added: PART 1 CRP630-03, Benchtop Pro Z-axis Cable Track Support SK-M6-16, M6 x 16mm Socket Head Cap Screw BHCS-M8-12, M8 x 12mm Button Head Cap Screw TNR-M8, M8 Roll-in T-nut 5 CRP630-02 - Benchtop Pro Y-axis Cable Track Bracket BHCS-M6-12, M6 x 12 mm Socket Head Cap Screw CRP621-01, Cable Track Moving Bracket CRP621-02, Cable Track Fixed Bracket...
-
Page 14: Step 13: Cable Track
Step 13: Cable Track Fasteners Added: PART BHCP-M6-12, M6 x 12mm Button Head Cap Screw Note: It may be easier to route your cables through the track prior to attaching the track to the support brackets. Instructions for how to operate the cable track can be found at: www.cncrouterparts.com/pro-cable-track- installation-instructions-p-273.html (See Part 2) Upper Cable Track...
Need help?
Do you have a question about the CRP600 Benchtop PRO and is the answer not in the manual?
Questions and answers