1. Manuals
  2. Brands
  3. AMTC Manuals
  4. Wireless Router
  5. PW5002
  6. User manual

AMTC PW5002 User Manual

Plc 600mbps wireless n 300mbps wi-fi router
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PW5002
PLC 600Mbps
Wireless N 300Mbps Wi-Fi Router
User Guide
公司名称：Shenzhen MTC Co.,LTD
产品名称：Wireless Router
产品型号：PW5002
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PW5002 and is the answer not in the manual?

Questions and answers

Related Manuals for AMTC PW5002

Summary of Contents for AMTC PW5002

  • Page 1 PW5002 PLC 600Mbps Wireless N 300Mbps Wi-Fi Router User Guide 公司名称：Shenzhen MTC Co.,LTD 产品名称：Wireless Router 产品型号：PW5002...

  • Page 2: Important Safety Instructions

    13. Unplug this product from the wall socket before cleaning. Use a damp cloth for cleaning. Do not use liquid cleaners or aerosol cleaners. 14. The specification of the fuse is for PW5002 to avoid damage, please do not change the fuse. 15. The Operating temperature is 0℃~40℃ (32℉~104℉). The Storage temperature is -40℃~70℃...

  • Page 3: Preface

    Thank you for choosing MTC! Please read this user guide before you start! This user guide instructs you to install and configure your device. This user guide applies to PW500X, The PW5002 is used as an example throughout this user guide. This user guide uses the following formats to highlight special messages:...

  • Page 4: Table Of Contents

    Contents Important Safety Instructions .......................... 2 Preface ................................3 Contents ................................4 Chapter 1 Introduction ............................ 6 1.1 Product Overview ..........................6 1.2 Product Feature ..........................6 Chapter 2 Connecting Mechanism ........................7 2.1 Appearance ............................7 2.1.1 The products front panel ......................7 2.1.2 The product rear panel ......................
  • Page 5 3.7.5 Remote WEB ......................... 53 3.7.6 WAN Ping ..........................55 3.8 Routing ............................55 3.9 Traffic Control ..........................56 3.10 System Tools ..........................57 3.10.1 Time Settings ........................57 3.10.2 Backup/Restore ........................59 3.10.3 Restore to Factory ......................60 3.10.4 Firmware Upgrade ......................61 3.10.5 Reboot ..........................

  • Page 6: Chapter 1 Introduction

    Wi-Fi Protected Access (WPA2- PSK, WPA-PSK), the device delivers complete data privacy. Conventions The device mentioned in this User Guide stands for PW5002 300Mbps Wi-Fi Router without any explanations. Parameters provided in the pictures are just references for setting up the product.

  • Page 7: Chapter 2 Connecting Mechanism

    Chapter 2 Connecting Mechanism 2.1 Appearance 2.1.1 The products front panel The LED indicator displays information about the device’s status. LEDs Name Status Indications Solid The device is on. Power LED The device is off. Blinking The device is in the pairing procedure. Solid The Ethernet port is connected.

  • Page 8: The Product Rear Panel

    The device isn’t connected to any router network Blinking The device is transferring data. The wireless function has been disabled. Wi-Fi/Wi-Fi The extender is cloning Wi-Fi settings from other Blinking Slow Clone device. Blinking Quickly The wireless function has been enabled 2.1.2 The product rear panel Button and Interface description (from right to left) ...

  • Page 9: Connection Instruction

    Ethernet cable).  TCP/IP network software (compatible with Window XP/Window 7/Window 8).  Internet Explorer 8 or higher versions or Firefox 2.3 Connection Instruction 2.3.1 Getting Prepared Before you start the installation process, you need to prepare the following things: Item Description Router...

  • Page 10: Installment Environment

    2. Internet connection information provided by the remote AP 3. Ethernet Cable: This can be found in the product package. You will need it to connect your PC to this device 2.3.2 Installment Environment Please follow these rules when install and use: 1.
  • Page 11 1) If you use ADSL connect the internet, please follow step 1-4 as graphical shown to connect your device. 2) If you use Residential broadband, put the network line into the WAN port and follow the step 3-4 as graphical shown to connect your device. Set Steps：...
  • Page 12 ② Click Network and Internet. ③ Click Network and Sharing Center.
  • Page 13 ④ Click Change adapter settings. ⑤ Click Local Area Connection and select Properties.
  • Page 14 ⑥ Select Internet Protocol Version 4 (TCP/IPv4) and click Properties. ⑦ Select Obtain an IP address automatically and click OK ⑧ Click OK on the Local Area Connection Properties window to save your settings...
  • Page 15 Note  If you need to configure the IP address manually, please set the PC’s IP address and router IP address in the same subnet, because the router’s default IP is 192.168.1.1, the subnet mask is 255.255.255.0, so your IP should set 192.168.1.XXX; XXX cannot be 1.

  • Page 16: Chapter 3 Configuring The Device Manually

    Tips  PW5002 as a Wifi Router device, avoid abnormal of IP conflict in the same LAN, after this device connected with up level router, it will adjust itself as follows: 1) If this device’s LAN IP and the up level router’s LAN IP at the same network segment, this device will change its LAN IP automatically.
  • Page 17 Tips  Default Password is “admin”  The default language is EN. You can change the language between English and French.  Web page layout Web page have：primary & secondary navigation bar、configuration zone、help information zone four parts，as shown: Note  Device does not support web page, function display will appear abnormal, please refer to the actual situation of equipment software.
  • Page 18 Name Description Primary User can easily Select functions in the navigation bar menu, Select the results displayed in the configuration Secondary section configuration zone Configure and view area. help information The help information of current page Note Change the resolution of the screen the help information may become “ ”...
  • Page 19 Note Change the resolution of the screen or login by small screen terminal, the “navigation bar menu” may become “ ” as above shown, if you want to refer the “navigation bar menu” please click the symbol.  Commonly used web page elements description Common elements Description Scan the information automatically...

  • Page 20: Quick Setup

    Close the scan function Close Scan Application current page configuration Apply Cancel current page configuration Cancel Save current page configuration Save Refresh current page configuration Refresh Add item Delete item Delete resumed to not configured mode resetOOB Backup current information Backup Upgrade current information Upgrade...
  • Page 21 Here are two modes Router and AP: Tips  The default mode is Router. You can change the operation mode on the quick setup page. 1) Router mode configure Plug Internet cable to PW5002 WAN port. Set steps: ① Select “Router”. ②...

  • Page 22: System Status

    Knowledge Expansion  AP: The most basic mode of multi-function is Access Point. In this mode, the AP will act as a central hotspot for different wireless LAN clients. In this mode, this device connect with up level router via Ethernet cable, and after connected, this device send wireless signal, you can surf the Internet through connection with the wireless signal.

  • Page 23: Wan Status

     System Version: Firmware Version.  Running Time: Displays the time duration indicating how long the router has been up since startup. Up time is recounted and renewed upon power off.  System Time: Current system time on this device. The device automatically synchronizes the system time with Internet time servers.

  • Page 24: Lan Status

     Primary DNS Server: Obtained from ISP.  Secondary DNS Server: Obtained from ISP.  Connection Duration: Access method for dynamic IP or PPPOE server and router and ISP connection is properly timed. Tips WAN IP/Subnet Mask/Gateway/Primary DNS Server/Secondary DNS Server: This types of information appears only if the router successfully connects to Internet via a PPPoE or DHCP (dynamic IP) connection.

  • Page 25: Wireless Status

    Tips  The default IP address is 192.168.1.1.  The default Subnet mask value is 255.255.255.0  If the router as a DHCP server, here shown as enabled. Otherwise disabled 3.3.4 Wireless Status Parameters Specification:  SSID Name：The name of Wireless. ...

  • Page 26: Network Settings

    Click “Network Settings” enter the Network setup web page，in this page you can set “WAN Settings”, “WAN Parameters”, “MAC Address Clone”. 3.4.1 WAN Settings Plug Internet cable to PW5002 WAN port. Set Steps： ① Enter the web and Select “Network Settings”.
  • Page 27 1、Configuration the Internet access Support Static IP mode、Dynamic IP(DHCP)、PPOE. Instruction WAN Connection Type If your ISP provides you with an Ethernet cable from the incoming Internet side IP information (IP address, subnet Static IP mode mask, gateway IP address, DNS server address), your ISP uses a static IP connection.
  • Page 28 Parameters Specification:  Connection Type: Select Static IP.  IP Address/Subnet Mask/WAN subnet mask/Gateway/Primary DNS Server/Secondary DNS Server: Enter the ISP information you gathered in Getting Prepared.  Click Save to save your settings. Tips  MTU better to choose the default values. 1.2>...
  • Page 29 Tips  MTU better to choose the default values. 1.3> PPOE Set Steps： ① Click “Network Settings”. ② Select “WAN Settings”. ③ Select Connection Type “PPOE”. ④ Enter the ISP login UserName，the ISP login Password. ⑤ Click “Save” to confirm.
  • Page 30 Knowledge Expansion  MTU: Maximum Transmission Unit. It is the size of the largest data packet that can be sent over the network. The default value is 1500. The common MTU sizes and applications are listed in the table below. Application 1500 Typical for connections that do not use PPOE or VPN.

  • Page 31: Wan Parameters

    3.4.2 WAN Parameters Set Steps： Click “Network Settings”. ① Select “WAN Parameters”. ② ③ Select Negotiation Mode type. ④ Click “Save” to confirm. Parameters Specification:  Negotiation mode: you can set the value to match with the status Tips 1. The router operates in “Auto-negotiation” (or Auto) mode by default. Usually, it works for most cases.

  • Page 32: Mac Address Clone

    3.4.3 MAC Address Clone Some ISPs (Internet Service Providers) require end-user's MAC address to access their network. This feature copies your current PC's MAC address to the router. Set Steps： ① Click “Network Settings”. ② Click “MAC Address Clone”. ③ You can set this page from three methods：...

  • Page 33: Wlan Settings

    Knowledge Expansion 1. Restore to Factory Default MAC: Reset the router’s WAN MAC to factory default. 2. Clone MAC: Clicking this button copies the MAC address of the computer that you are now using to the router. Also, you can manually enter the MAC address that you want to use. You have to use the computer whose MAC address is allowed by your ISP 3.5 WLAN Settings Click “WLAN Settings”...
  • Page 34 Parameters Specification:  Wireless: wireless “Enable” or “Disable”.  SSID: It is the unique name of the wireless network and can be modified.  Broadcast (SSID): Select “Enable” to enable the router’ SSID to be scanned by wireless devices. The default is enabled. If you disable it, the wireless devices must know the SSID for communication.

  • Page 35: Security Settings

    Tips 1. The SSID is PW5002_XXXXXX by default, where XXXXXX is the last six characters in the device's MAC address. You can find it on the label attached on the bottom of the device. 2. If you are not an advanced user, it is advisable to only change the SSID (name of the network) and channel and leave other items unchanged.
  • Page 36 Parameters Specification:  Security mode: WPA – Personal、WPA2 – Personal、Mixed WPA/WPA2 – Personal. Security mode Instruction Disable Not open this function WPA – Personal Support AES and TKIP cipher types WPA2 – Personal Support AES, TKIP and TKIP+AES cipher types Both WPA-Personal and WPA2-Personal secured Mixed WPA/WPA2 –...
  • Page 37 Parameters Specification:  WPA Algorithms: Wi-Fi Protected Access Algorithms.  Pass Phrase: The default is 123456. Knowledge Expansion 1. WEP: (Wired Equivalent Privacy) is the wireless transmission of data between two devices for encryption, to prevent illegal users wiretapping or invade the wireless network. 2.

  • Page 38: Wps Settings

    Tips  Recommended that you choice “WPA-Personal” + ”AES” mode , make sure the wireless efficiency and ensure the security of wireless network. Meanwhile, avoid some kind of wireless network card does not support security mode, cause cannot connect the wireless network.
  • Page 39 The WPS provides two methods: PBC and PIN to achieve the function it provides  PBC: Using routers and physical or logical button on a wireless device to connect WPS.  PIN: Using routers and PIN for WPS connection on a wireless device. You have four methods to connect WPS: 1、...

  • Page 40: Access Control

    Knowledge Expansion resetOOB:  The router wireless SSID, safe mode resumed to not configured mode. Make the WPS reset the SSID, Encryption and password, after the completion of the reset, the router’s SSID is factory default, safe mode is unencrypted. 3.5.4 Access Control Wireless access control is actually based on the MAC address to permit or forbid specified clients to access the wireless network...
  • Page 41 2. Select “Allow” allow ONLY the specified wireless clients to join your wireless network. 3. Select “Block” disallow ONLY the specified wireless clients to join your wireless network. Wireless Access Control Application Example: To only allow your own notebook at the MAC address of 00:12:35:EC:DF:25 to join your wireless network Set Steps：...

  • Page 42: Connection Status

    3.5.5 Connection Status This page shows the current wireless access list Click “Refresh” to update. Tips  The bandwidth here refers to the channel bandwidth instead of wireless connection rate.  You can know whether there are unauthorized accesses to your wireless network by viewing the wireless client list.
  • Page 43 Set Steps： ① Click “Network Settings”. ② Select “LAN Settings”. ③ Enter IP Address，Subnet Mask. ④ Click “Save” and wait for the router reboot automatically. Parameters Specification:  MAC Address：It displays the Router’s LAN MAC address.  IP Address：It displays the Router’s LAN IP address. ...

  • Page 44: 2Dhcp Server

    3.6.2DHCP Server Set Steps： ① Click “LAN Settings”. ② Select “DHCP Server”. Parameters Specification:  DHCP Server: Select whether enable or disable the DHCP server feature.  Start IP Address and End IP Address: You can specify the starting and ending address of the IP address pool here.

  • Page 45: Dhcp List & Binding

    Tips By default, the router functions as a DHCP server. Do not disable the DHCP server feature unless you want to manually configure the TCP/IP settings for all PCs on your LAN. 1. Lease time will be renewed automatically upon expiry. No additional configurations are needed.
  • Page 46  Click “Refresh” to update the related DHCP client information. Tips  You can know whether there are unauthorized accesses by viewing the client list.  Also, you can specify a reserved IP address for a PC in the LAN. That PC will always receive the same IP address each time when it accesses the DHCP server.

  • Page 47: Expert Settings

    2. For PCs that has already obtained IP addresses, you may need to perform the Repair action to activate the configured static IP addresses 3.7 Expert Settings Click “Expert Settings” enter the Virtual Server configure page ,here you can set “URL Filter”, “Port Range”, “DMZ Settings”, “DDNS”, “Remote WEB”, “WAN Ping”.
  • Page 48 URL Filter Application Example: To prevent your home PC (192.168.1.100) from accessing “YouTube” from 8:00 to 18:00 during working days: Monday- Friday. Set Steps： ① Enter a Policy Name ② Enter the Start IP and End IP here for example:192.168.1.100 ③...

  • Page 49: Port Range

    3.7.2 Port Range You want to share resources on your PC with your friends who are not in your LAN. But, by default, the router's firewall blocks inbound traffic from the Internet to your computers except replies to your outbound traffic. You can use the Port Forwarding feature to create exceptions to this rule so that your friends can access these files from external networks.

  • Page 50: Dmz Settings

    Parameters Specification:  Start/End Port: Enter the start/end port number which ranges the External ports used to set the server or Internet applications. Here in this example, enter 21.  IP Address: Enter the IP address of the PC where you want to set the applications. Here in this example, enter 192.168.1.100.

  • Page 51: Ddns Settings

    ⑤ Click “Save” to confirm. Tips  The DMZ Settings screen allows one local computer to be exposed to the Internet for use of a special-purpose service such as Internet gaming or videoconferencing.  DMZ hosting forwards all the ports at the same time to one PC. Note 1.
  • Page 52 Set Steps： ① Click “Expert Settings” ② Select “DNNS” ③ DNNS Service Enable ④ Add “Serve provider”. ⑤ Enter the “User name” and “Password” ⑥ Enter “Domain Name” ⑦ Click “Save” to confirm. Tips 1. To use the DDNS feature, you need to have an account with one of the Service Providers in the drop-down menu first.

  • Page 53: Remote Web

     Domain name: Enter the effective registered domain name. 3.7.5 Remote WEB This section is to allow the network administrator to manage the router remotely. If you want to access the router remotely, please select “Enable”. Set Steps： ① Click “Expert Settings”. ②...
  • Page 54 2. Make sure your WAN IP address (Internet IP address) is a public IP address. Private IP addresses are not routed on the Internet. 3. It is unsafe to make your router remotely accessible to all PCs on external network. For better security, we suggest that only enter the IP address of the PC for remote management Remote Web Management Application Example: To access your router (WAN IP address: 172.16.87.160) at your home from the PC (210.16.87.154)

  • Page 55: Wan Ping

    2. Port: This is the management port to be open to outside access. The default setting is 8080. This can be changed 3.7.6 WAN Ping The ping test is to check the status of your internet connection. When disabling the test, the system would prevent the ping test from WAN.

  • Page 56: Traffic Control

     Destination IP: The IP address of the final destination. “0.0.0.0” indicates any network segment.  Subnet Mask: The subnet mask for the specified destination.  Gateway: This is the next router on the same LAN segment as the router to reach. ...

  • Page 57: System Tools

    ⑧ In the list table you can Edit or Delete the configure. ⑨ Click “Save” to save your settings. Tips 1. 1M=128KByte/s. 2. The volume of uplink traffic/downlink traffic should not be larger than that allowed on your router's WAN (Internet) port. You can ask your ISP to provide the volume of Internet traffic. 3.
  • Page 58 Tips Configured time and date info will be lost if the device gets disconnected from power supply. However, it will be updated automatically when the device reconnects to Internet. To activate time-based features (e.g. firewall), the time and date info shall be set correctly first, either manually or automatically Set Steps：...

  • Page 59: Backup/Restore

    Tips If the router connected to the Internet, the device’s time and network time synchronization by default. 3.10.2 Backup/Restore Parameters Specification:  Backup: Click this button to back up the router's configurations.  Restore: Click this button to restore the router's configurations. Set Steps：...

  • Page 60: Restore To Factory

    “.cfg” when renaming the file name to avoid problem. 3.10.3 Restore to Factory Set Steps： ① Click “System Tools”. ② Select “Restore to Factory”. Parameters Specification:  This “Restore” button is to reset all configurations to the default values. It means the Range Extender will lose all the settings you have set.

  • Page 61: Firmware Upgrade

     Do not restore factory default settings unless the following happens: 1> You need to join a different network or unfortunately forget the login password. 2> You cannot access Internet and your ISP or our technical support asks you to reset the router.

  • Page 62: Reboot

    firmware may damage the device. 2. It is advisable that you upgrade the device's firmware over a wired connection. DO NOT interrupt the power to the router when the upgrade is in process otherwise the router may be permanently damaged. 3.10.5 Reboot When a certain feature does not take effect or the device fails to function correctly, try rebooting the device.

  • Page 63: System Log

    Set Steps： ① Click “System Tools” ② Select “Change Password” ③ Enter “Old Password” “New Password” and “Confirm New Password” ④ Click “Save” to save you settings. Tips  The default login password is admin.  The valid password must be between 3~12 characters and only include letters, numbers and underscore 3.10.7 System Log The section is to view the system log.
  • Page 64 Set Steps： ① Click “System Tools” ② Select “System Log” ③ Click “Refresh” can update the information ④ Click “Clear” to clear the screen...

  • Page 65: Appendix

    Appendix 1 Configure PC TCP/IP Settings Windows 7 ① Click Start -> Control Panel.
  • Page 66 ② Click Network and Internet. ③ Click Network and Sharing Center.
  • Page 67 ④ Click Change adapter settings. ⑤ Click Local Area Connection and select Properties.
  • Page 68 ⑥ Select Internet Protocol Version 4 (TCP/IPv4) and click Properties.
  • Page 69 ⑦ Select Obtain an IP address automatically and click OK.
  • Page 70 ⑧ Click OK on the Local Area Connection Properties window to save your settings.

  • Page 71: Windows Xp

    Windows XP ① Right-click My Network Places and select Properties. ② Right click Local Area Connection and select Properties.
  • Page 72 ③ Select Internet Protocol Version 4 (TCP/IPv4) and click Properties. ④ Select Obtain an IP address automatically and click OK.

  • Page 73: Troubleshooting

    ⑤ Click OK on the Local Area Connection Properties window to save your settings. 2 Troubleshooting The Troubleshooting provides answers to common problems regarding the Router Adapter： 1. The Power LED does not light up. Ans. Check the following: a) Make sure that the Router Adapter is properly plugged into a power outlet. b) Make sure the power outlet is active (working) by plugging another electric device into it.

  • Page 74: Factory Default Settings

    Ethernet port. b) Make sure that the other end of the Ethernet cable (RJ-45) is properly connected to the computer LAN card or to you Cable/xDSL Ethernet port. c) Make sure your computer LAN card is properly installed and configured. d) Make sure your Cable/xDSL broadband access is working and configured correctly.

  • Page 75: Remove Wireless Network From Your Pc

    Subnet Mask 255.255.255.0 （LAN） DHCP Server Enabled IP Pool 192.168.2.100~192.168.2.200 (GMT+08:00)Beijing, Time Zone Chongqing, Hong Kong, Urumqi Wireless Enabled MTC_XXXXXX(where XXXXXX last characters in the device's SSID MAC address) You can find it on the label attached to the device. Wireless Network Mode 11b/g/n mixed...

  • Page 76: Windows 7

    your PC; otherwise, you may not be able to wirelessly connect to this device. Below describes how to remove a wireless network from your PC. Windows 7 ① Right-click the Network icon and select Properties. ② Select Manage Wireless Networks.
  • Page 77 ③ Select the wireless network and click Remove network.

  • Page 78: Windows Xp

    Windows XP ① Right-click My Network Places and select Properties. ② Right click Wireless Network Connection and then select Properties.

  • Page 79: Safety And Emission Statement

    NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable Hereby, Shenzhen MTC Co.,LTD declares that this Wireless Router(PW5002) is in compliance with...
  • Page 80 the essential requirements and other relevant provision of Directive 1999/5/EC. The declaration of monformity may be consult at Manufacture Name: Shenzhen MTC Co.,LTD Manufacture Address: MTC Industry Park,1st Lilang Rd, Xialilang Community, Nanwan Street, Longgang District, Shenzhen FCC Statement FCC ID: 2AHVHPW5002 This device complies with Part 15 of the FCC Rules.
  • Page 81 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &...

Table of Contents