Advertisement
DIGITAL SECURITY SYSTEM
Your cordless headset uses a digital security system to protect against false
ringing, unauthorized access, and charges to your phone line.
porta
ver install telephone wiring during a lightning storm.
designed for wet locations.
ver touch non-insulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
Use caution when installing or modifying telephone lines.
Temporarily disconnect any equipment connected to the phone such as
faxes, other phones, or modems.
porta
Install near an electrical power outlet.
Your headset charge cradle should be placed on a level surface such as a
desk or table top.
Avoid sources of noise, such as a window by a busy street, and electrical
Avoid heat sources, such as heating air ducts, heating appliances, radiators,
and direct sunlight.
Avoid areas of excessive moisture or extremely low temperature.
Avoid dusty locations.
Avoid other cordless telephones or personal computers.
TALLA
Certa
communic
requenc
communic
ter r
a
y
concerne
ter rence
r
devic
o t
roperl
a
INSTALLING THE HEADSET BATTERY
Y
m
connec
c approve
Pol
ter
o
1. If the battery door is attached, press on both sides of the battery compartment
cover and lift the cover up and o .
2. Insert the battery into the battery compartment with the label Warning facing
up.
3. Push the battery plug into the connector inside the compartment according to
the color-coded label and place the wires neatly inside the compartment.
4. Insert the tab on the bottom of the battery cover into the battery compartment.
Press down gently on the battery cover until it snaps into place.
5. Place cordless headset in charger. Plug the power supply cord into the power
jack on the bottom of the charger and the other end into an electrical outlet.
Place headset in the charger. Within a few seconds, the charge indicator should
illuminate, verifying the battery is charging.
charge the unit, battery performance is compromised.
NOTE: Remove the ear hook from the headset before battery replacement.
power adaptor listed in the user's guide. This power adaptor is intended to be
Class (Classe) 2 Power source
c
and
roperl
t
c
telephone
y
ar
t
o
r'
anu
t
v
ter rence.
ter b
r
e.
T
HEADSET SET UP
Headband Attachment
To attach the headset to the headband for wearing on the left or right ear:
1. Remove ear hook if currently attached
to the headset.
2. Insert the earpiece into the headband
ring.
3. Push the earpiece towards the
headband ring until it clicks into place.
comfortably. Adjust and rotate the angle
of the headset until the microphone is
pointing toward your mouth.
NOTES:
To wear on the other ear, rotate the headset within the headband ring.
Firmly grip the padded earpiece with one hand whenever adjusting the
headset microphone up or down . To remove the headset from the
headband: Hold the headset with one hand and the headband ring with
the other hand. Twist and pull the headset gently until it separates from
the ring of the headband.
NOTES:
When you use the headband, you can use the highest in ear tip to keep
the volume state.
EAR HOOK ATTACHMENT
To attach the ear hook to he headset.
1. Remove the headband if currently
attached to the headset.
2. Insert the earpiece into the ear hook.
3. Press the ear hook onto the earpiece
until it clicks into place
4. Hook the headset onto the desired ear.
Adjust the angle of the headset until the
microphone is pointing towards your
mouth.
Note: Insert ear hook into either side of ear hook ring, matching with
TO SWITCH FROM EAR TO EAR
Unplug the ear hook from ear hook ring.
Insert the ear hook to ear hook ring with L mark for Left ear.
Insert the ear hook to R mark for Right ear.
Rotate microphone boom to reposition nearer to mouth.
your ear. Gently manipulate into the desired shape for maximum comfort.
IN EAR ATTACHMENT
If the Earplug is bigger or smaller than your ear, you can change the In Ear tip for
maximum comfort.
Advertisement
