1. Manuals
  2. Brands
  3. ARA Manuals
  4. Gate Opener
  5. PY500AC
  6. User manual

ARA PY500AC User Manual

Sliding gate operator
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Sliding Gate Operator
User's Manual
PY
PY5 5 5 5 00
PY
00
00A A A A C C C C
00
PY

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PY500AC and is the answer not in the manual?

Questions and answers

Related Manuals for ARA PY500AC

Summary of Contents for ARA PY500AC

  • Page 1 Sliding Gate Operator User's Manual PY5 5 5 5 00 00A A A A C C C C...

  • Page 2: Table Of Contents

    PY500AC SLIDING GATE OPERATOR OUTLINE 1. Products introduction ……………………………………2 2. Important safety precautions ……………………………2 ……………………………2 3. Main technical parameters 4. Mechanical Installation …………………………………2 ………………………………………………5 5. Adjustment 6. Wire Connecting …………………………………………6 7. Turning and operation ……………………………………8 8. Programming Process ……………………………………10 ……………………………………………14 9.

  • Page 3: Products Introduction

    Installation Installation Installation The PY500AC will handle gate weighting up to 500kg and up to 12m if the proper installation procedures have been followed. The PY500AC gate operator operates by forcing a drive rack by a drive gear. The entire configuration...
  • Page 4 Gate operator Fig.1 Gate preparation Be sure the gate is properly installed and slides smoothly before installing the PY500AC sliding gate operator. The gate must be plumb, level, and move freely. Conduit In order to protect the cable, use PVC conduit for low voltage power cable and control wires. Conduit must be preset into the concrete when it is poured.
  • Page 5 PY500AC SLIDING GATE OPERATOR Gate operator Gear Spring washer Plain washer Groundsill Input power Fig.2 Operator base (see Fig.3) After the concrete has hardened, mount the gate operator base to the concrete pad. Verify that the base is properly leveled.

  • Page 6: Adjustment

    PY500AC SLIDING GATE OPERATOR � When the rack has been installed, to ensure it meshes correctly with the gear. � The space between rack and gear is about 0.5mm. Fig.4 Fig.4 Fig.4 Fig.4 5. 5. 5. 5. Adjustment Adjustment Adjustment...

  • Page 7: Wire Connecting

    PY500AC SLIDING GATE OPERATOR M6X10 Fig.6 Manual operation In case of power failure use key unlock the lock and pull down the release bar about 90 degree to open or close gate manually, use the release key as follow: �...
  • Page 8 Fig.9 infrared infrared Schematic diagram d. Three-button switch / single-button switch (keypad): The PY500AC is equipped with interfaces for three-button switch and single-button switch (keypad). To install the keypad attach one lead of your keypad to ‘OSC’ of terminal X1 and the other to the...

  • Page 9: Turning And Operation

    PY500AC SLIDING GATE OPERATOR For three-button switch installation, use the terminals for multi-channel mode. Connect open wire of external button switch to ‘OPEN’ of terminal X1, connect close wire of switch to ‘CLOSE’, connect stop wire of switch to ‘STOP’, connect common wire of switch to ‘COM’.
  • Page 10 PY500AC SLIDING GATE OPERATOR Button 1 Button 2 Button 3 Button 4 Fig.12 Remote transmitter � Adding extra remote controls (Learn): Remove the cover, press the learn button ‘SW1’ (Fig.8), then the ‘LED2’ (Fig.8) will be on and turn off, then press the remote control button which you want to use, the ‘LED2’...

  • Page 11: Programming Process

    PY500AC SLIDING GATE OPERATOR 8. 8. 8. 8. Porgramming Porgramming Porgramming Porgramming Process Process Process Process Table of the DIP-switch (SW2) Position DIP-switch Function SET Limit switch mode is NC. Limit switch mode is NO. Auto-close function and auto-close function of pedestrian mode are available.
  • Page 12 PY500AC SLIDING GATE OPERATOR through. Set width of pedestrian mode: Turn on the second and the third DIP-switch (See Fig.9) to ON position. Verify open direction Press button 4 to open the gate (see Verify Verify Verify open open open direction...
  • Page 13 PY500AC SLIDING GATE OPERATOR Cancel width of pedestrian mode, keep auto-close function of pedestrian mode: Turn on the second Verify Verify open open and the third DIP-switch (See Fig.9) to ON position. Press button 4 to open the gate (see Verify...
  • Page 14 PY500AC SLIDING GATE OPERATOR weight. weight. weight. weight. � Adjustment of the auto-reverse function: rotate the ‘W1’ knob (Fig.8) by hand, the resistance may be increased or decreased by rotating clockwise or counterclockwise. Note: if the gate fails to reverse in the event of obstruction, then the opening force or closing force should be checked for conformity with requirements and adjusted accordingly.

  • Page 15: Maintenance

    PY500AC SLIDING GATE OPERATOR If the gate stops at closed position when the limit switch is reached, the gate will not move if you press ‘CLOSE’ button. � � � � The device is installed with a thermal protector, the thermal protector will switch off the motor automatically in case of the temperature is higher than 120°C and switch on the motor automatically...

Table of Contents