Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ARA PY300DC
Summary of Contents for ARA PY300DC
- Page 1 SLIDING GATE OPERATOR USER’S MANUAL PY300DC...
-
Page 2: Table Of Contents
OUTLINE 1. PRODUCTS INTRODUCTION 2. IMPORTANT SAFETY PRECAUTIONS 3. MAIN TECHNICAL PARAMETERS 4. MECHANICAL INSTALLATION 5. ADJUSTMENT 6. WIRE CONNECTING 7. ELECTRICAL AND CONTROL BOARD 8. PROGRAMMING PROCESS 9. MAINTENANCE 10. TROUBLE SHOOTING 11. PACKING LIST... -
Page 3: Products Introduction
PRODUCTS INTRODUCTION 3. MAIN TECHNICAL PARAMETERS PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE Unit Model PY300DC PROCEEDING. Power Supply 220VAC/110AC THE OPERATOR CONTAINS EXTRA BATTERY, TRANSFORMER, CONTROL BOARD AND RADIO CONTROL. IN CASE OF POWER Max gate weight 300Kg FAILURE, THE OPERATOR IS POWERED BY A 24V DC, 4.0AH, Max gate width EXTRA BATTERY. -
Page 4: Mechanical Installation
4. MECHANICAL INSTALLATION GATE PREPARATION THE PY300DC WILL HANDLE GATE WEIGHTING UP TO 300KG AND UP TO BE SURE THE GATE IS PROPERLY INSTALLED AND SLIDES SMOOTHLY BEFORE 8M IF THE PROPER INSTALLATION PROCEDURES HAVE BEEN FOLLOWED. INSTALLING THE PY300DC SLIDING GATE OPERATOR. THE GATE MUST BE PLUMB, LEVEL AND MOVE FREELY. - Page 5 INSTALLATION OF RACK • FIX THE THREE NUTS (IN THE SAME PACKAGE WITH RACK) ON THE RACK ELEMENT • LAY THE FIRST PIECE OF RACK ON THE GEAR AND WELD THE FIRST NUT ON THE GATE. • MOVE THE GATE MANUALLY, CHECKING IF THE RACK IS RESTING ON THE GEAR, AND WELD THE SECOND AND THIRD NUT.
-
Page 6: Adjustment
5. ADJUSTMENT MANUAL OPERATION IN CASE OF POWER FAILURE, USE MANUAL RELEASE KEY TO OPEN NOTE: THE GATE OPERATOR NEEDED RESET LIMIT AFTER RE-TIGHT OR CLOSE THE GATE MANUALLY, USE THE RELEASE KEY AS FOLLOW: THE CLUTCH, BY TURNING THE KEY COUNTERCLOCKWISE IF THE POWER FAILURE –... -
Page 7: Wire Connecting
6. WIRE CONNECTING 7. ELECTRICAL AND CONTROL BOARD CONNECTING THE BATTERY PLUG THE TERMINAL OF EXTRA BATTERY IN THE CONTROL BOARD. NOTE: IF YOU NOT USE GATE OPERATOR AND POWER FAILURE, PLEASE PULL OUT THE EXTRA BATTERY TERMINAL (FIG 7). CONNECTING THE MOTOR MOTOR: GREEN WIRE TO T1 AND RED WIRE TO T2. -
Page 8: Programming Process
SET OPEN AND CLOSE POSITIONS 8. PROGRAMMING PROCESS PRESS AND HOLD SET UNTIL NUMBER 1 IS INDICATED ON THE LED DISPLAY. SET BUTTON – MODE SET AND CONFIRM FUNCTION PRESS AND HOLD OPEN TO SET OPEN POSITION (NOT THE DOOR MUST BE CODE BUTTON –... -
Page 9: Maintenance
AUTOMATIC CLOSE (0-90 SECONDS ADJUSTABLE) PHOTO BEAM CONNECT THE PHOTO BEAM – FOLLOW FIGURE. THE PHOTO BEAM OUTPUT SIGNAL MUST BE N.C. 1. PRESS AND HOLD OPEN UNTIL ‘-’ IS INDICATED ON THE LED DISPLAY SIGNAL 2. PRESS OPEN TO INCREASE THE AUTO CLOSE TIME, PRESS CLOSE TO DECREASE TIME. PRESS AND HOLD CLOSE UNTIL ‘=‘... -
Page 10: Troubleshooting
AFTER RECEIVING THE GATE OPERATOR, YOU SHOULD MAKE AN UNPACK INSPECTION, IN WHICH YOU SHOULD CHECK WHETHER THE PRODUCT WAS DAMAGED. IF YOU HAVE ANY PROBLEM, YOU SHOULD CONTACT OUR DEALER. YOU SHOULD FIND THE FOLLOWING ITEMS IN OUR STANDARD PACKING: Item Quantity Py300dc sliding gate operator Hand transmitter Release key User’s manual...
Need help?
Do you have a question about the PY300DC and is the answer not in the manual?
Questions and answers