Advertisement
Available languages
Available languages
OBJ_BUCH-1125-005.book Page 12 Friday, February 26, 2016 11:29 AM
12 | English
max.
[mm]
[mm]
D
b
d
180
8
22.2
D
230
8
22.2
b
D
180
–
230
d
100
30
M 14
b
D
Rotating the Main Handle (3 601 H92 F../
3 601 H92 G../3 601 H92 H../3 601 H93 F../
3 601 H93 G../3 601 H93 H../3 601 H93 J../
3 601 H95 F../3 601 H95 H..)
Before any work on the machine itself, pull the mains
plug.
The main handle 29 can be rotated with respect to the ma-
chine housing toward the left or right in steps of 90°. In this
manner, the On/Off switch can be brought into a more con-
venient position for special working situations, e.g., for cut-
ting operations using the cutting guide with dust extraction
protection guard 25 or for left-handed persons.
Press the handle unlocking button 30 in the direction of the
arrow and at the same time turn the main handle 29 to the re-
quested position until it latches.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
1 609 92A 2CA | (26.2.16)
-1
d
[min
]
[m/s]
8500
80
Prevent dust accumulation at the workplace. Dusts can
6500
80
Operation
8500
80
–
6500
80
Starting Operation
Observe correct mains voltage! The voltage of the pow-
8500
45
When operating the machine with power from mobile genera-
tors that do not have sufficient reserve capacity or are not
equipped with suitable voltage control with starting current
amplification, loss of performance or untypical behavior can
occur upon switching on.
Please observe the suitability of the power generator being
used, particularly with regard to the mains voltage and fre-
quency.
Switching On and Off
To start the power tool, press the On/Off switch 3 forward
and then down.
To lock-on the pressed On/Off switch 3, push the On/Off
29
switch 3 further forward.
30
To switch off the power tool, release the On/Off switch 3, or
when it is locked, briefly press the On/Off switch 3 and then
release it.
Switch Version without Lock-on (country-specific):
To start the power tool, press the On/Off switch 3 forward
and then down.
To switch off the machine, release the On/Off switch 3.
Check grinding tools before using. The grinding tool
Kickback stop
(GWS 24-180 LVI/GWS 24-230 LVI/GWS 26-230 LVI)
On/Off switch 3 to the Off position and start the machine
again.
Note: When the machine only runs with heavily reduced
speed, the kickback stop feature has failed. The power tool
must promptly be sent to an after-sales service agent for
maintenance; addresses, see Section „After-sales Service
and Application Service".
– As far as possible, use a dust extraction system suita-
ble for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
easily ignite.
er source must agree with the voltage specified on the
nameplate of the machine.
must be mounted properly and be able to move freely.
Carry out a test run for at least one minute with no load.
Do not use damaged, out-of-centre or vibrating grind-
ing tools. Damaged grinding tools can burst and cause in-
juries.
In case of a sudden drop in speed, e.g.,
caused by a jammed disc while cutting, the
power supply to the motor is electronically
interrupted.
To restart the operation, switch the
Bosch Power Tools
Advertisement
