Anywire ASLINKSENSOR Product Manual

AnyWireASLINK System Products Guide
ASLINKSENSOR
[Photoelectric Diffuse Reflection Type (IP67)]
BS-H0317-1K
[Notes on Safety]
Precautions that must be observed in order to use this system safely are
indicated as shown below. You must observe these precautions.
A WARNING indicates a potentially hazardous situation which, if not
WARNING
！
handled correctly, could result in death or serious injury.
A CAUTION indicates a potentially hazardous situation which, if not
CAUTION
！
handled correctly, may result in personal injury or property damage.
○ System Safety
！
WARNING
This system is intended for general industrial applications. It does not
have functions for supporting applications requiring higher levels of
safety such as safety-related devices or accident prevention systems.
The product must not be used for these purposes.
○ Always turn off the power before attempting to mount or replace.
○ Prolonged continuous ow of a rated load current or higher or a transit
current due to load short-circuit, etc., in the hybrid unit including the
output unit and the output circuit may result in smoking or ring. An
external safety device such as a fuse must be installed.
○ System power supply
！
CAUTION
Use a stable, 24V DC power supply. Use of an unstable power supply
may cause problems with the system.
○ Separately route high-voltage and power cables
Although the AnyWireASLINK has a high noise margin, lay the transmis-
sion lines and I/O cables so as to keep them away from high-voltage
and power cables.
○ Connectors and terminals
・ Pay careful attention to the length and installation of cable wiring to
ensure that connectors and cables are neither stressed nor discon-
nected even if they are stressed.
・ Make sure to prevent any metal objects from getting inside the
connectors or the terminal blocks.
・ Short-circuits caused by metal objects or mis-wiring are likely to
damage the device.
○ Do not impose any external loads on the units. Doing so may cause a
failure.
○ Do not disconnect or reconnect between the transmission line and slave
units. A malfunction may occur.
○ Use the AnyWireASLINK within the range of the speci cations and
conditions shown below.
[Warranty]
■ Warranty period
The warranty on the delivered Product shall continue to be effective for one (1)
year after the delivery thereof to a location as designated by the original owner.
■ Scope of warranty
Should a defect occur in any part of the Product during the foregoing warranty
period when it is used normally in acordance with the speci cations described in
this User's Manual, the Company shall replace or repair the defect free of
charge, except when it arises as a result of:
[1] Misuse or abuse of the Product by the owner;
[2] Fault caused by other than the delivered Product;
[3] The unauthorized modi cation or repair of the Product by any person other
than the Company's personnel;
[4] Any unusual force of nature, disaster or other cause beyond the Company's
control.
The term "warranty," as used herein, refers to the warranty applicable to the
delivered product alone. The Company shall not be liable for consequential or
incidental damages resulting from any malfunction.
■ Repair at cost
After the expiration of the warranty period, the owner shall be responsible for all
costs and expenses incurred for the troubleshooting and repair of the Product.
Even during the warranty term, the Company shall repair any defects arising
from causes other than within the scope of the warranty as speci ed above, at
the owner's cost.
[Type]
AnyWireASLINK photoelectric sensor:
Diffuse re ection type, bit operation
BS-H0317-1K 1 optical axis
-BSH03171K 1/8-
[Function]
Model ASLINKSENSOR 2-wire (non-insulation)
Detection method Diffuse re ection type
Sensitivity adjustment value (threshold)
Hysteresis
Alarm judgment value
Alarm judgment time
Light ON/dark ON
Operation mode
Function
Light receiving display switching
Delay timer
One shot
Sensing level drop
Slave unit voltage drop
Waterproof (IP67)
[Contents in package]
BS-H0317-1K
*Please purchase the attachment tting separately.
*An "address writer ARW-04 (Ver.04-1.01 or higher)" is required for setting to
the unit. Prepare it together.
ARW-04
Front
[Name of each part]
■Diffuse re ection type
Setting port
LINK indicator
DP (Red)
DN (Black)
Unit ... 1 unit
The version is
displayed when
POWER is on.
A "Ver.*.**" is
READER/WRITER
described on
ARW-04
Ver.04-1.01
LotNo.***
MADE IN JAPAN
this label.
Back
Input indicator
ALM indicator
Light emitting surface
Attachment tap 2-M3
Transmission cable