Page 1
DRAFT 3 TD9300 Data Terminal Installation Manual MNE-00003-01 · Issue 1 · March 2015...
Page 2
Code, or in any other way convert the Object Code into without prior written permission from Tait Limited. a human-readable form. Protected by U.S. Patents The words TAIT, TAITNET and the TAIT logo are 5,870,405, 5,826,222, 5,754,974, 5,701,390, registered trademarks of Tait Limited.
It includes information on installing the TD9300 in a TN9300 DMR trunked network. Document Conventions The TD9300 data terminal has a web interface with an accordion menu on Rewrite this when UI is the left side of the screen. “Configuration > Users” means click finalised.
The characters xx represent the issue number of the documentation. Technical notes are published from time to time to describe applications for Tait products, to provide technical details not included in manuals, and to offer solutions for any problems that arise. Look for new or updated technical notes on the Tait Technical Resources website.
Antenna Load Transmitting into a low VSWR will maximize the power delivered to the antenna. Notice Do not remove the load from the TD9300 while it is transmit- ting. Load transients (switching or removing the load) can damage the transmitter.
The humidity should not exceed 95% relative humidity through the specified operating temperature range. 1.3.3 Dust and Dirt The TD9300 has the following ingress protection ratings: IP40 ■ IP51 (dust category 2) with the front panel connectors facing down. ■...
1.4.5 Unauthorized Modifications Any modifications you make to this equipment which are not authorized by Tait may invalidate your compliance authority’s approval to operate the equipment. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
DRAFT 3 Introduction The TD9300 Data Terminal is an element of the Tait solution for grid automation on electricity distribution networks. It uses its RF capability to connect over the Tait DMR Tier III trunked network to exchange DMR control channel and packet data messages with the Tait SCADA Gateway.
Figure 3.3 on page 18). These holes allow the TD9300 to be mounted flat against the DIN rail. Up to two units may be mounted in this way across a 19 inch rack or cabinet. Notice Make sure that the mounting rail is strong enough to bear the weight of the TD9300 units without bending.
Ethernet The Ethernet interface is used to connect the TD9300 to the RTU/ IED or to the network. It is also used to configure the TD9300 via a web browser. It is a 10BASE-T or 100BASE-T connection. The green link speed LED indicates the negotiated link speed. The LED is lit when the link speed is 100BASE-T.
Page 21
RTU Status LED The green RTU status LED is lit when the RTU is linked to the TD9300. DMR LED The green DMR LED is lit when the TD9300 is registered on the DMR network. 1 LED Reserved for future use.
The TD9300 is powered down by disconnecting the front panel DC What about a shutdown connector. process for the Linux console? The pin allocations for the DC input on the TD9300 are given in the following table. Description –V input +V input...
DRAFT 3 Getting Started Confirming Operation The LEDs on the front and top panels will indicate that the TD9300 is operating correctly. Connect power to the TD9300. Check that the LEDs indicate normal operation, as described below. Color State Power...
“Designated Products” means products pro- vided by Tait; and (iii) may contain one or more vided by Tait to Licensee with which or for which items of software owned by a third-party sup- the Software and Documentation is licensed for plier.
Page 32
Tait during the course of the inspec- for use by third parties on a "time sharing," tion will be kept in strict confidence by Tait and "application service provider," "service bureau" used solely for the purpose of verifying...
Page 33
Tait demonstrating compli- investigation of the perceived defect reveals that ance with all the foregoing. no such defect in fact exists, Tait may recover its Section 8 TERM AND TERMINATION costs in respect of such investigation from 8.1.
Page 34
Tait to the repair or replacement without first obtaining such license or approval. of the Software or the refund of the purchase 11.10.