Advertisement
S
e
t t
n i
g
h t
e
p
e
n
d
u
u l
m
T
h
e
a
d
u j
s
a t
b
e l
p
e
n
d
u
perfect cutting stroke for different materials.
•
Slide the selector (10) to the desired position
referring to the table below. The selector can be
manipulated during operation.
Pos.
Wood
2
Fast cuts
2
Thick workpieces -
1
Plywood
Chipboard
0
Thin workpieces Sheet metal
Fine cuts
M
o
u
t n
n i
g
h t
e
p
a l
t s
c i
(fig. D)
T
h
e
a
n
- i t
c s
a r
c t
h
s
h
o
e
to the surface of (sensitive) workpieces.
•
Click the cover onto the shoe as shown.
When appropriate, connect a dust
extraction system designed in
compliance with the applicable
directives regarding dust emission.
Do not use a dust extraction system
without proper spark protection when
sawing metal.
Instructions for use
•
Always observe the safety instructions
and applicable regulations.
•
Make sure your workpiece is well secured.
Remove nails, screws and other
fasteners that may damage the blade.
•
Check that there is sufficient space for
the blade underneath the workpiece.
Do not cut materials that exceed the
maximum cutting depth of the blade.
•
Use sharp saw blades only. Damaged
or bent saw blades must be removed
immediately.
• Do not use the tool for sawing pipes or
tubes.
t s
o r
k
e
i f (
. g
A
)
u l
m
t s
o r
k
e
g
u
a
a r
n
e t
e
s
Metal
Plastics
-
PVC
Fibreglass
Acrylic
Aluminium
-
Non-ferrous
-
-
a
n
i t
s -
c
a r
c t
h
s
h
o
e
c
c
o
v
r e
1 (
) 2
e r
d
u
c
e
s
d
•
a
•
•
•
S
w
i
c t
h
n i
g
o
v
r e
DW341(K)
•
To run the tool, press the on/off switch (1).
a
m
a
g
e
•
For continuous operation, press and hold down
the switch (1), press the lock-on button (2) and
release the switch.
•
To stop the tool, release the switch.
•
To stop the tool in continuous operation, press
the switch briefly and release it. Always switch
off the tool when work is finished and before
unplugging.
Setting the electronic sawing speed (fig. E)
D
W
3
4
1
(K)
T
h
e
s
a
w
n i
g
on the on/off switch (1).
•
To preset the sawing speed, turn the control dial
(3) to the desired level. The higher the rate, the
higher the sawing speed. The required setting
depends on the thickness and kind of material.
Use high speeds for sawing soft materials such
•
as wood. Use low speeds for sawing metal.
Holding the tool (fig. F)
•
Hold the tool as shown.
-
D
W
3
4
Never run your tool without a saw blade.
For optimal results, move the tool
smoothly and constantly over the
workpiece. Do not exert lateral pressure
on the saw blade.
Keep the shoe flat on the workpiece
and lead the cord away in line with the
tool. When sawing curves, circles or
other round shapes, push the tool
gently forward.
Wait until the tool has come to a standstill
before removing the saw blade from the
workpiece. After sawing the blade may
be very hot. Do not touch.
o
n
a
n
d
o
f f
i f (
. g
A
)
i f (
. g
E)
s
p
e
e
d
v
r a
e i
s
i w
h t
h t
e
After using the tool for an extended period
on low speed settings, run it for approx.
3 minutes on maximum no-load speed.
1
(K)
:
i f
. g
F
E N G L I S H
p
e r
s s
u
e r
e
x
r e
e t
d
9
Advertisement
