Page 1
Smart 1000 Spot-Beam-Wash This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place User manual Please read the instructions carefully before use...
1. Safety Instructions Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. Unpack and check carefully there is no transportation damage before using the unit. ...
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals.
5. Operating Instructions The moving head is for spot effect for on-site decoration purpose. Don’t turn on the fixture if it’s been through severe temperature difference like after transportation because it might damage the light due to the environment changes. So make sure to operate the fixture until it is in normal temperature.
Page 6
Check if rigging clamp (not including the one inside) is damaged or not and if it stands ten times weight as the equipment. Make sure the architecture can stand ten times weight as all the equipment, clamps, wiring and other additional fixtures. ...
7. DMX-512 Control Connections This product accepts the international standard DM 512 ( 1990) of the digital control signal. Please use the 3 pin or 5pin XLR plugs&socket offed by factory to connect the first projector’s input to the second projector output, and connect the second projectors output to the third projectors input and so on.
Page 8
Mode 3 Screen Rotation Touch rectify Tilt Focus Colour Test Gobo Prism Frost Strobe Pan invert Tilt invert P/T rectify on Advanced setup Pan Offset Tilt Offset Lamp up when Reset done Power on Manual Factory setting Sure Work mode Address Version Statue setup...
Page 9
2. Set Light work mode Enter the page of ‘WORK MODE’ and modify settings. You can set light work mode, control lamp and DMX channel mode. Light includes 3 working modes: DMX MODE, AUTO RUN and SOUND MODE. Parameters are defined as following: ...
STROBE: range for 0 to 255 5. Set light run parameters Enter the page, set the parameter of light: Pan Invert: Reverse PAN move. Tilt Invert: Reverse TILT mover. Rectify enable:set as ‘OFF’, PAN or TILT will disable position rectify function. ...
Page 11
18-26 Deep Blue 27-36 Yellow 37-45 Green 46-54 Magenta 55-63 Azure 64-72 73-81 Dark green 82-90 Amber 91-100 Blue 101-109 Orange 110-118 119-127 UV filter 128-129 White 130-134 Deep Red 135-138 Deep Blue 139-143 Yellow 144-147 Green 148-152 Magenta 153-157 Azure 158-161 162-166...
Page 14
250-255 No rotation 1-127 Forward gobo rotation from slow to fast Gobo rotation 128_129 No rotation 130-255 Backwards gobo rotation from slow to fast 0-19 Open position (hole) 20-49 6-face linear rotating prism -indexing 50-75 6-face linear rotating prism- rotation 76-105 8-face circular rotating prism- Indexing 106-127...
Page 15
0-31 Shutter closed ( Lamp power reduced to 230 W) 32-63 Shutter open, Full lamp power 64-95 Strobe-effect from slow to fast 96-127 Shutter open 128-143 Opening pulse in sequences from slow to fast CH15 shutter 144-159 Closing pulse in sequences from fast to slow 160-191 Shutter open 192-223...
Page 16
91-100 Blue 101-109 Orange 110-118 119-127 UV filter 128-129 White 130-134 Deep Red 135-138 Deep Blue 139-143 Yellow 144-147 Green 148-152 Magenta 153-157 Azure 158-161 162-166 Dark green 167-171 Amber 172-176 Blue 177-180 Orange 181-185 186-189 UV filter 190 - 215 Forwards rainbow effect from fast to slow 216 - 217 No rotation...
200-207 Macro 10 208-215 Macro 11 216-223 Macro 12 224-231 Macro 13 232-239 Macro 14 240-247 Macro 15 248-255 Macro 16 No rotation 1-127 Forwards prism rotation from fast to slow Prism CH15 rotation 128-129 no rotation 130-255 Backwards prism rotation from slow to fast Open 1-179 Frost from 0%to 100 %...
Page 20
Clean the inside and outside lens each week to avoid the weakness of the lights due to accumulation of dust. Clean the fan each week. A detailed electric check by approved electrical engineer each three month, make sure that the circuit contacts are in good condition, prevent the poor contact of circuit from overheating.