H3C S5800 Configuration Manual
Hide thumbs
Also See for S5800:
- Configuration manual (438 pages) ,
- Installation manual (101 pages) ,
- Quick start manual (33 pages)
Subscribe to Our Youtube Channel
Related Manuals for H3C S5800
Summary of Contents for H3C S5800
- Page 1 H3C S5820X&S5800 Switch Series OAA Configuration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 1211 Document version: 6W100-20110415...
- Page 2 SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V G, V G, PSPT, XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd. All other trademarks that may be mentioned in this manual are the property of their respective owners Notice The information in this document is subject to change without notice.
- Page 3 The OAA Configuration Guide describes OAA fundamentals and configuration. It describes how to log in to the H3C open application platform (OAP) card connected to your switch and reset the operating system of the OAP card, and configure the ACFP and ACSEI protocols to exchange information between your switch and the OAP card.
- Page 4 Conventions This section describes the conventions used in this documentation set. Command conventions Convention Description Boldface Bold text represents commands and keywords that you enter literally as shown. Italic Italic text represents arguments that you replace with actual values. Square brackets enclose syntax choices (keywords or arguments) that are optional. Braces enclose a set of required syntax choices separated by vertical bars, from which { x | y | ...
- Page 5 Represents a routing-capable device, such as a router or Layer 3 switch. Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports Layer 2 forwarding and other Layer 2 features. About the H3C S5800&S5820X documentation set The H3C S5800&S5820X documentation set includes: Category...
- Page 6 Guides you through installing SFP/SFP+/XFP Transceiver Modules transceiver modules. Installation Guide • S5800-60C-PWR Switch Video Installation Guide Shows how to install the H3C S5800-60C-PWR and • H3C S5820X-28C Ethernet switches. S5820X-28C Switch Video Installation Guide Describe software features and configuration Configuration guide procedures.
- Page 7 Obtaining documentation You can access the most up-to-date H3C product documentation on the World Wide Web at http://www.h3c.com. Click the links on the top navigation bar to obtain different categories of product documentation: [Technical Support & Documents > Technical Documents] –...
-
Page 8: Table Of Contents
Contents OAP card configuration ·············································································································································· 1 OAP card overview ··························································································································································1 Configuring an OAP card················································································································································1 Logging in to the software system of an OAP card through the switch······························································1 Restarting an OAP card···········································································································································2 ACFP configuration ······················································································································································ 3 Introduction to ACFP ·························································································································································3 ACFP architecture·····················································································································································3 ACFP collaboration ··················································································································································4 ACFP management···················································································································································4 ACFP information overview·····································································································································5... -
Page 9: Oap Card Configuration
• You can install multiple OAP cards on some models of the S5800 and S5820X switches. If you log in to the software system of one OAP card first, you cannot log in to the software system of another by using the oap connect command. -
Page 10: Restarting An Oap Card
Restarting an OAP card If the software system of an OAP card works abnormally or is under other anomalies, restart the OAP card with the following command. Follow the step below to restart an OAP card: To do… Use the command… Remarks Required oap reboot slot slot-number... -
Page 11: Acfp Configuration
ACFP configuration This chapter includes these sections: Introduction to ACFP • ACFP configuration task list • Configuring the ACFP server (switch) • Configuring the ACFP client (OAP card) • Introduction to ACFP Basic data communication networks comprise of routers and switches, which forward data packets. As data networks develop, more and more services run on them. -
Page 12: Acfp Collaboration
Interface-connecting component—It connects the interface of the routing/switching component to • that of the independent service component, allowing the devices of two manufacturers to be interconnected. ACFP collaboration ACFP collaboration means that the independent service component can send instructions to the routing/switching component in order to change its functions. -
Page 13: Acfp Information Overview
NOTE: The S5800&S5820X switches support the mirroring and redirect modes only. • The S5800&S5820X switches support carrying the preamble HGPlus as the context ID (the • HGPlus-context) only. The above-mentioned information indicates the collaboration capabilities of an ACFP server. ACFP clients can access this information through a collaboration protocol or collaboration MIB. - Page 14 Out-interface—Interface through which the packet is forwarded normally. • • Dest-interface—ACFP server interface connected with ACFP client. Context ID—Used when the packet is mirrored or redirected to an ACFP client. After the interface • connected to the ACFP client is specified in the policy sent, the ACFP server assigns it a global serial number (the Context ID) with each Context ID corresponding to an ACFP collaboration policy.
-
Page 15: Using Acfp
You can use the collaboration policy to manage the collaboration rules that belong to it. Using ACFP The S5800 and S5820X switches can be installed with various types of OAP cards. If you install an • IPS card on the switch, disable STP on the internal 10 Gigabit Ethernet port that connects the IPS card to the switch. -
Page 16: Acfp Configuration Task List
ACFP redirects and mirrors any IP datagram not greater than 1,500 bytes—length of Layer 3 packet, • excluding link layer header—but discards any IP datagram greater than 1,500 bytes. ACFP configuration task list Complete the following tasks to configure ACFP: Task Remarks Enabling the ACFP server... -
Page 17: Displaying And Maintaining Acfp
Trap message Level Expiration period of ACFP collaboration policy timed notifications The generated traps will be sent to the information center of the device. With the parameters for the information center set, the output rules for traps—whether the traps are allowed to be output and the output destinations—are decided. -
Page 18: Acsei Configuration
ACSEI configuration This chapter includes these sections: Introduction to ACSEI • ACSEI server configuration (switch) • ACSEI client configuring (OAP card) • Introduction to ACSEI As a private protocol, ACSEI provides a method for exchanging information between ACFP clients and ACFP server. -
Page 19: Acsei Timers
ACSEI timers An ACSEI server uses two timers, the clock synchronization timer and the monitoring timer. The clock synchronization timer periodically triggers the ACSEI server to send clock synchronization • advertisements to ACSEI clients. You can set this timer through command lines. •... -
Page 20: Configuring The Clock Synchronization Timer
Configuring the clock synchronization timer Follow these steps to configure the clock synchronization timer: To do… Use the command… Remarks Enter system view system-view — Enable the ACSEI server function acsei server enable Required Enter ACSEI server view acsei server —... -
Page 21: Displaying And Maintaining Acsei Server
Displaying and maintaining ACSEI server To do… Use the command… Remarks display acsei client summary [ client-id ] [ | Display ACSEI client summary { begin | exclude | include } regular-expression ] Available in any view display acsei client info [ client-id ] [ | Display ACSEI client information { begin | exclude | include } regular-expression ]... -
Page 22: Index
Index A C I O Configuring the ACFP server (switch),8 ACFP configuration task list,8 ACSEI client configuring (OAP card),13 Introduction to ACFP,3 ACSEI server configuration (switch),1 1 Introduction to ACSEI,10 Configuring an OAP card,1 OAP card overview,1 Configuring the ACFP client (OAP card),9...
Need help?
Do you have a question about the S5800 and is the answer not in the manual?
Questions and answers