Deluce Lighting DLPAN10WBLKDL Fitting Instructions page 2

These instructions are for the Déluce Lighting Panther LED Floodlights :
DLPAN10WBLKDL, DLPAN10WBLKWW, DLPAN10WBLKDLPIR, DLPAN10WBLKWWPIR, DLPAN20WBLKDL, DLPAN20WBLKWW,
DLPAN20WBLKDLPIR & DLPAN20WBLKWWPIR DLPAN30WBLKDL, DLPAN30WBLKWW, DLPAN30WBLKDLPIR, DLPAN30WBLKWWPIR,
DLPAN50WBLKDL, DLPAN50WBLKWW, DLPAN50WBLKDLPIR & DLPAN50WBLKWWPIR
MAINTENANCE
1. Please make sure the power is switched off before starting any
maintenance.
2. In order to maintain good even light coverage, the glass cover
should be cleaned regularly.
PIR ADJUSTMENT (FOR PIR MODELS)
On the base of the PIR there are three (3) dials:
Sensor Range ( SENS )
This dial sets the floodlight's sensitivity to movement.
Turning the dial clockwise will adjust the sensitivity range,
as follows :
up to 10mtrs x 140° degree spread (approx).
TIME DIAL ( TIME )
This dial controls how long the light will remain on once
activated.
It will operate from 5 Seconds to 8 Minutes. Turning the
dial fully clockwise will set the unit to it longest time
setting and fully anti-clockwise will set it at its shortest
setting.
DAYLIGHT ADJUSTMENT DIAL ( LUX )
This dial sets the floodlight to be activated at different
light levels. To set the light to activate only after dark, wait
until dusk and turn the dial completely anti-clockwise.
Slowly turn the dial clockwise until the light comes on.
The light will now activate after dusk.
PLEASE NOTE - TO OPERATE UNDER MANUAL OVERRIDE :
When the fitting is installed and operating normally under automatic control from the PIR it can be switched to permanent
operation by simply switching the power off and on again within 3 seconds (the fitting will now be on all the time!).
To change the operation back to automatic control through the PIR simply switch the fitting off again and wait a minimum of
7 seconds. After 7 seconds switch the power back on and the fitting will again be under automatic control through the PIR (the
fitting will only be activated and switched on when movement is detected).
GUARANTEE
This product is guaranteed in the EU for a period of 1 year from the date of purchase. The guarantee is invalid in the case of improper use, installation, tampering, removal of the
QC date label, installation in an improper working environment or installation not according to the current edition of the IEE Wiring Regulations (BS 7671). Should this product
fail during the guarantee period it will be replaced free of charge, subject to correct installation and return of the faulty unit. Déluce Lighting does not accept responsibility for any
installation costs associated with the replacement of this product. Your statutory rights are not affected. Déluce Lighting reserves the right to alter specifications without prior notice.
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION
LEAVE A COPY FOR THE USER/MAINTENANCE ENGINEER FOR FUTURE REFERENCE
We recommend this fitting is installed by a qualified Electrician.
www.delucelighting.com
LED PANTHER
FLOODLIGHT FITTING
INSTRUCTIONS
3. For good heat dissipation the floodlight housing should also be
cleaned regularly.
4. Please take care when cleaning the glass or floodlight housing.
DO NOT USE water or cleaning solutions, cleaning should
preferably be done with a clean dry cloth.
SENS
RANGE ADJUSTMENT
The PIR sensor is situated on a moveable joint.
The sensor range can be adjusted by moving the PIR both
vertically and horizontally.
Please be aware that PIR detectors are more sensitive
to movement across them than they are to movement
towards them. This should be considered when
positioning during installation.
SPECIFICATIONS
Detection Method:
Time Adjustment:
Power Consumption: 6 Watts maximum for the sensor
TIME LUX
Passive infrared sensor
5 seconds to 8 minutes (approx)
unit only
DEL0585a/Feb_2016/issue_1 page 2 of 2