Advertisement
Quick Links
Advertisement
Related Manuals for Dahua ITARD-024SA
Summary of Contents for Dahua ITARD-024SA
- Page 1 ITARD-024SA Radar User’s Manual Version 1.0.0...
-
Page 2: Table Of Contents
Table of Contents General Introduction ........................1 Features ............................2 Specifications ..........................3 Dimensions ..........................4 Installation............................ 5 FAQ .............................. 8 Appendix Toxic or Hazardous Materials or Elements ..............9 FCC Warning………………………………………………………………………………………..10... - Page 3 Welcome Thank you for purchasing our device! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!
- Page 4 Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC (24V AC) in the IEC60950-1. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.
-
Page 5: General Introduction
In the actual environments, we can see the wave beam level width of the radar shall be less than 7° . The ITARD-024SA adopts the 4.6° angle. To avoid the interference from the vehicle out of the beam, the side lobe level of the antenna direction shall be general low. -
Page 6: Features
2 Features Adopt flat micro beam array antenna design and manufacture technology. It can get the commonness easily, light weight and high efficiency. The speed measuring accuracy is high and the error ranges from -1km/h to +1km/h. High reliability. -
Page 7: Specifications
3 Specifications Model ITARD-024SA Spec Antenna Type Flat micro beam array antenna Radar Single-frame continuous beam Mechanism Microwave 24.125GHz 50MHz Working Frequency Send Power 9.5dBm=8.9mW Antenna 3dB 4.6° (H) ×6.8° (V) Beam Width AD Sampling 25KHz Rate Working Mode... -
Page 8: Dimensions
4 Dimensions Please refer to the following figure for detailed information. The unit is mm. See Figure 4-1. Figure 4-1... -
Page 9: Installation
5 Installation ITARD-024SA high-performance narrow beam flat radar detect min speed is 10Km/h. It can not directly provide the vehicle direction. The width of the microwave beam level and tilt is less than 3dB and usually it is used in the ANPR (Auto Number Plate Recognition). - Page 10 Please note the above angle is for reference only. Please select the reasonable snap position. Usually, the nearer the distance is, it is easy to distinguish the vehicles one by one. But the speed error correction value may be high， and vice versa. Besides, the radar wave beam level width is fixed 3dB.
- Page 11 Brown Step5 Connect the power cable and boot up the device; you can see the indication light is on. See Figure 5-4. Radar power indication light Figure 5-4...
-
Page 12: Faq
6 FAQ Radar is a professional product of high technology and high sensitivity. Please read the user’s manual carefully before you use. There output, Check power connection and voltage response, after I connected Check power positive end and the negative end connection the power to the device. -
Page 13: Appendix Toxic Or Hazardous Materials Or Elements
Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component Device ○ ○ ○ ○ ○ ○ Construction Material Wire and ○ ○ ○... -
Page 14: Fcc Warning
Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation. CAUTION: changes or modifications not expressly app roved by the party responsible for compliance could void the user's authority to operate the equipment.