1. Manuals
  2. Brands
  3. LaView Manuals
  4. IP Camera
  5. LV-PB784F2
  6. User manual

LaView LV-PB784F2 User Manual

4mp mini network bullet camera
Hide thumbs Also See for LV-PB784F2:
Table of Contents

Advertisement

Quick Links

User Manual
IP Camera User Manual
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LV-PB784F2 and is the answer not in the manual?

Questions and answers

Related Manuals for LaView LV-PB784F2

Summary of Contents for LaView LV-PB784F2

  • Page 1 User Manual IP Camera User Manual...

  • Page 2: Table Of Contents

    User Manual Contents Introduction ............................... 3 1. Overview ............................... 4 1.1 Range of Application ..........................4 1.2 Product Description ..........................5 1.3 Operation Environment ........................5 2. Device Connection ............................6 3. Device Operation Instructions ........................7 3.1 Check Connection ..........................7 3.2 Searching Device ..........................
  • Page 3 7. Alarm Parameter ............................31 7.1 Mobile Detection ..........................31 7.2 I/O Alarm (if applicable) ........................33 7.3 Lens Blocking............................33 8. Device ................................. 34 8.1 SD Card（optional function） ......................34 8.2 Audio ..............................35 8.3 Logs ............................... 35 9. System Parameters ........................... 36 9.1 Basic Information ..........................

  • Page 4: Introduction

    Introduction Thank you for using our network camera products. Our network camera products are integrated and developed for network video monitoring, including Storage Network Bullet, Wireless Storage Network Bullet, IR Network Dome, IR Network Weather-Proof Cameras and High-Speed Network Ball. High-performance single SOC chips are used in media processor for audio/video acquisition, compression and transmission/transfer.

  • Page 5: Overview

    1. Overview 1.1 Range of Application The network cameras with powerful image processing capacity may be applied at various public places such as mall, supermarket, school, factory and workshop, as well as in environments requiring HD video image such as bank and traffic control system, as shown below: Monitoring Center...

  • Page 6: Product Description

    1.2 Product Description An IP camera is a digital online surveillance camera embedded with Web server and capable of independent operation, giving user access to real-time monitoring through web browser or client software from any place across the world. IP camera is based on the latest Hisilicon solution, an integrated media processing platform for audio/video acquisition, compression and network transmission on a single board.

  • Page 7: Device Connection

    2. Device Connection IP camera can be connected in two ways: 1. Connection to PC Connect IP camera to PC via straight-through network cable, with power input connected to a DC 12V adaptor, and set the IP addresses of the PC and IP camera in one network segment. The IP camera will communicate with PC within one minute after being powered on if the network operates normally.

  • Page 8: Device Operation Instructions

    3. Device Operation Instructions 3.1 Check Connection The default factory IP address for IP camera is 192.168.1.168 and the subnet mask is 255.255.255.0. Allocate to your computer an IP address in the same network segment as the IP camera, for example, 192.168.1.69, and a same subnet mask as that of the IP camera. Test whether the IP camera is connected properly and started normally by clicking on Start >...

  • Page 9: Searching Device

    3.2 Searching Device Tips: IPC Device Search may be used for device searching across network segments. Before running IPC Device Search, click on the local connection icon at the lower right corner of the desktop; 1. Add IP addresses of several network segments in TCP/IP setting for local connection (as shown below).
  • Page 10 Online device searching procedure 1. Run IPC Device Search by double clicking icon . It will search and display any online IPC and its IP address, port number, number of channels, device type and version, subnet mask, gateway, MAC address and connection pattern.
  • Page 11 Upgrade： it can offer 1pcs or more than 1pcs IP camera upgrade.Please choose the IP camera you want to upgrade in the left frame,Open the icon to choose the software you want ,put in the user name and password, the press the right corner button to upgrade. Config: Double-click the selected camera in the search page, turn to the Config page to reboot the camera, change passwords, and reset the camera.

  • Page 12: Installation Of Controls And Login To System

    3.3 Installation of Controls and Login to System Before using IE (Internet Explorer) browser to access the IP camera for the first time, related plug-in components must be installed by following the procedure below: Access IP address of the IP camera to automatically load the controls from it. In a pop-up plug-in installation dialog box, choose an installation option to perform the installation process.

  • Page 13: Preview

    3.3.1 Preview Operate IE and enter the IP address of the camera (http://192.168.1.168) to open a login box as shown below:...
  • Page 14 In the login box you can choose a language for the IE client. Enter your user name (admin by default) and password (admin by default) and then press OK to open a preview frame as shown below: Some buttons in the preview frame are described below. : Color setting button, for setting of color, brightness, contrast, saturation and sharpness of the frame.

  • Page 15: Playback（Optional Function

    : Access to device setting menu, for customized setting of various device parameters. : For setting of snapshot, video file type and storage path. : Help information (including current user, Web browser and plug-in versions), logout button, for returning to the login page. :Video preview switch enable/disable, original preview frame ratio, automatic preview frame ratio, full preview frame from the left to the right.
  • Page 16 User can search video by file type as needed, and operate the video through the simple tool on the toolbar, e.g. open/stop video , bit stream video, recording, snapshot, download recording , quick motion video playback, Sound On/Off.

  • Page 17: Parameter Setting

    4 Parameter Setting 4.1 Display Configuration Click on Parameter Setting to open the page as below (preview setting page by default): Name of channel: name of the IP camera Display of channel: Choose to display or conceal it. Time display: Choose to display or conceal it. Blinking control: Choose 50Hz, 60Hz or disable it.

  • Page 19: Image Control

    4.2 Image Control Click on Image Control in Display Configuration to open the following page: IR-Cut Model: Classified into GPIO Automatic, Colored, and Black-White models. Delay: IR-cut switching delay. Corridor mode and Angle rotation (0° 、180° ) Image Flip-Over: including flip horizontal flip vertical Image Control: backlight compensation, 3D noise reduction, WDR, automatic gain, shutter speed, exposure time and de-moist model.

  • Page 20: Video Blocking

    4.3 Video Blocking Click on Video Blocking in Display Configuration to open the following page: Procedure of setting video blocking: Check Enable Video Blocking Press down and hold the left mouse button and drag out a area for video blocking (up to four areas at one time) Click on Save to enable the video blocking area.

  • Page 21: Roi (If Applicable)

    4.4 ROI (if applicable) Click on ROI in Display Configuration to open the following page: Procedure of setting ROI: Choose an area of application Press down and hold the left mouse button and drag out a ROI area (only one ROI can be set for each area) Click on Save to apply the ROI area.

  • Page 22: Record Parameters

    area. Range of frame rate is in relation to video standard and resolution. (Note: Different non-ROI frame rates may be allocated to different ROI areas, but the minimum value among them is used as the frame rate to be applied for the non-ROI area on the preview frame. ） 5.Record Parameters 5.1Rec Parameters Click Rec Parameters under the menu Record, go to below page...

  • Page 23: Network Parameters

    As image: one grid in the table is 30 minutes, green is normal record, yellow is motion detection alarm, red is I/0 User can setup according to private requirement to choose different record type and time。 6. Network Parameters 6.1 Network Parameters Click on Network Parameters in Network Parameter Menu to open the following page:...
  • Page 24 Networking mode: DHCP (Automatically Acquired), Manually Configured and PPPOE; the default is Manually Configured Media port: Media port for IPC Web port: Web port for IPC IP address: IP address of IPC Subnet mast: Subnet mast of IPC Default gateway: Default gateway of the device Preferred/Alternate DNS server: Set DNS server UPNP: Enable or disable UPNP function for the device (enabled by default) Note: To enable UPNP, the media/web/cell phone port should be set to a value between 1024-65535;...

  • Page 25: Bit Stream Setting

    6.2 Bit stream setting Click on Bit Stream Setting in Network Parameter Menu to open the following page: By default the available bit streams are: main bit stream, sub-bit stream and cell phone bit steam. You can set resolution, frame rate, video encoding, encoding level, audio, I frame interval, variable frame rate and bit stream size respectively for main bit stream, sub-bit stream and cell phone bit steam.

  • Page 26: E-Mail Configuration

    Bit stream: Set bit stream value by choosing fixed value or customizing it. Note: Range of main bit stream is 256-8192. Range of sub-bit stream is 128-4096. Range of cell phone bit steam is 8-1536. Video encoding and encoding level are unavailable in setting page of IP camera of 2MP Series. 6.3 E-Mail Configuration Click on E-Mail Configuration in Network Parameter menu to open the following page: E-Mail Configuration: mail service setting - used with alarm function to upload images snapped to the...
  • Page 27 Enable e-mail: Enable or disable e-mail function. SSL： ON/OFF SSL proto Port: The default port number is 25 (mail serve port). SMTP server: Enter the address of mail server. Address of sender: Address of sending mailbox. Password of sender: Password of sending mailbox. Address of recipient: Address of receiving mailbox.

  • Page 28: Ddns Configuration

    6.4 DDNS Configuration Click on DDNS Configuration in Network Parameter menu to open the following page: DDNS configuration: Dynamic DNS configuration - used with server for access from an extranet. Enable DDNS: Enable or disable it. Address of server: Choose "3322". Name of host: Enter the name of active server User name: Name of the user Password: Password of the user...

  • Page 29: Ip Filtering

    6.5 IP Filtering Click on IP Filtering in Network Parameter menu to open the following page: Filtering mode: Three modes are available (Allow all IP connections, Allow all IP connections as set, Forbid IP connection as set). Add: Add any allowed or forbidden IP address Delete: Delete any IP address added previously 6.6 RTSP Click on RTSP in Network Parameter menu to open the following page:...
  • Page 30 RTSP Enabling: Enable or disable RTSP. RTSP is enabled by default. After it is disabled, it will not be found with ONVIF.

  • Page 31: Ftp

    RTSP Port: The default port number is 554, and can be changed to another value between 1024 and 65535. Modification to the parameter will restart the system. Operation Instructions: For IP cameras of 3MP/4MP/5MP/8MP Series: rtsp://IP:Port/ch00/A A:0 (main bit stream), 1(sub-bit stream), 2 (cell phone bit stream) For IP cameras of 2MP Series: rtsp://IP:Port /A A:0 (main bit stream), 1(sub-bit stream), 2 (cell phone...

  • Page 32: Alarm Parameter

    FTP Server: Enter the address of FTP server. Port:FTP service port number; the default number is 21. Transmit Image: Check it to transmit image 7. Alarm Parameter 7.1 Mobile Detection Click on Mobile Detection in Alarm Parameter menu to open the following page: Procedure of setting Mobile Detection: Check Enable Mobile Detection.
  • Page 33 preview frame)

  • Page 34: I/O Alarm (If Applicable)

    7.2 I/O Alarm (if applicable) Click on I/O Alarm in Alarm Parameter menu to open the following page: I/O Alarm Input: Enable or disable I/O alarm. I/O Alarm Output Time: Set I/O alarm output time (10s, 20s, 40s, 60s) Recording Delay Time: After checking Enable Triggered Recording, you can set recording delay time (5S/10S/20S/30S) 7.3 Lens Blocking Click on Lens Blocking in Alarm Parameter menu to open the following page:...

  • Page 35: Device

    Security Level: Set security level for lens blocking (Level 1~8; larger value indicates higher security level) Mail Linkage: It is disabled by default. After enabled, it may be used with SMTP to enable mail delivery. 8. Device It includes SD Card（optional function） Logs and Audio. Their interfaces and functions are described below.

  • Page 36: Audio

    8.2 Audio Click on Audio in Device menu to open the following page: Procedure of setting Audio: Check Open Audio option to access audio setting, and set audio input/output volume (ranging 0~10), and then click on Save to save the parameters set. (Note: For application of audio function, the audio option in Bit Stream Setting needs to be enabled) 8.3 Logs Click on Logs in Device menu to open the following page:...

  • Page 37: System Parameters

    Log Type: Eight types of logs are available - system logs, network logs, parameter logs, alarm logs, user logs, recording logs, storage logs and all logs). Choose the starting and ending date/time for retrieval. Click on "Search" to retrieve and display related logs in the table below. Click on "Delete"...
  • Page 38 The device time, system time, date format and time format contained in the basic information can be manually set and saved. Three automatic time correction functions are provided in this device.
  • Page 39 DST: Check Daylight Savings Time (DST) option to enable DST correction. The device will correct the time based on the time deviation as set. NTP: Check Enable NTP option, input the address of time server and choose a time zone and then save the setting. The system will correct time in accordance with the time server.
  • Page 40 9.3 System Information Click on System Information in System Parameters menu to open the following page: Here some system information on the device will be displayed, including device type, MAC address and software version. You can visit mobile app through P2P QR code directly。...

  • Page 41: Advanced

    10. Advanced It includes System Update, Default Parameters and System Maintenance. Their interfaces and functions are described below. 10.1 System Update Click on System Update in Advanced menu to open the following page: Update will be unavailable if the update files do not match the target device. 10.2 Default Parameters Click on Default Parameters in Advanced menu to open the following page:...

  • Page 42: System Maintenance

    Check relevant options and click on Save to recover the default factory settings for the options as checked. 10.3 System Maintenance Click on System Maintenance in Advanced menu to open the following page: 、 Here you can set regular restart or manual restart of the device.

  • Page 43: Intelligent

    11. Intelligent 11.1 Smart Schedule one grid in the table is 30 minute,User can setup according to private requirement to choose different record type and time。...

  • Page 44: Smart Analysis

    11.2 Smart Analysis This page can correctly show the different time period’s line crossing count ( including different years , months and weeks’ line crossing count). User can search the video according to the recording types, alarm types and the beginning time of the recording. 11.3 Perimeter Intrusion Detection（PID）...

  • Page 45: Line Crossing Detection（Lcd

    Latch Time：when trigger alarm, the external alarm device ouput alarm time, can selected time period is 5S,10S, 20S, 30S. Post Recording：after triggered alarm, the post record time, selected time period is 5S, 10S, 20S, 30S Sensitive：Sensitive level, range is 1-4, default to 2. If the detected object sensitivity is more high, the moving Object can be detected easily.

  • Page 46: Stationary Object Detection

    Switch：LCD master switch Latch Time：when trigger alarm, the external alarm device ouput alarm time, can selected time period is 5S,10S, 20S, 30S. Post Recording： after triggered alarm, the post record time, selected time period is 5S, 10S, 20S, 30S Sensitive： Sensitive level, range is 1-4, default to 2.
  • Page 47 Function description: in the preview page, detect the lost and leave behind object in one fixed area Switch：LCD master switch Latch Time：when trigger alarm, the external alarm device ouput alarm time, can selected time period is 5S,10S, 20S, 30S. Post Recording： after triggered alarm, the post record time, selected time period is 5S, 10S, 20S, 30S Sensitive：...

  • Page 48: Pedestrian Detection(Pd)

    11.6 Pedestrian Detection(PD) Function description: in the preview page, detect the moving pedestrian. 【Switch】 ： Enable/ Disable 【Latch Time】 ：when trigger alarm, the external alarm device output alarm time, can selected time period is 5S,10S, 20S, 30S. 【Post Recording】 ： after triggered alarm, the post record time, selected time period is 5S, 10S, 20S, 30S 【Level】...

  • Page 49: Face Detection（Fd

    Rule Switch：The switch to every rule, Eanble/disable. Rule Type：Setup to each rule, default to Normal. 11.7 Face Detection（FD） Function description: in the preview page, detect the moving face. 【Switch】 ：Enable/ Disable 【Latch Time】 ：when trigger alarm, the external alarm device output alarm time, can selected time period is 5S,10S, 20S, 30S.

  • Page 50: Cross Counting(Fd)

    【Scene】 ：Scene setup, only support indoor. Enable I/O Out：Trigger alarm then if will be I/O output Send Email：If trigger alarm, send the Email to notify, the Email setup need to set in Remote Setting –Network-Email Record：if to do record. Rule Number：Max set 1 rule number. Rule Switch：The switch to every rule, Eanble/disable.
  • Page 51 【Level】 ：range is 1-4, default to 2. If the detected object sensitivity is more high, the moving Object can be detected easily. Meanwhile, the false detection rate is higher. Suggest to use default level. 【Scene】 ：Scene setup, only support indoor. Enable I/O Out：Trigger alarm then if will be I/O output Send Email：If trigger alarm, send the Email to notify, the Email setup need to set in Remote Setting –Network-Email...

Table of Contents

Save PDF