Introduction Thank you for purchasing the Ubiquiti Networks® UniFi® Application Server. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents UniFi Application Server Rack-Mount Brackets Bracket Screws Mounting Screws (Qty. 2) (Qty. 8) (Qty.
Page 3
Network Topology Requirement A DHCP-enabled network (for the UniFi Server to obtain an IP address) UniFi Application Server UniFi Switch US-16-XG UniFi Security Gateway Pro (DHCP Server) Internet The UniFi Controller and UniFi Video software applications are pre-installed on the UniFi Server. Use SSH and standard Ubuntu commands to configure the UniFi Server.
Hardware Overview Back Panel Ports IPMI LAN LAN1-2 Power USB1-2 Port Description Connect the included Power Cord to the Power Power port. (Optional) The dedicated RJ45 port supports IPMI LAN IPMI (Intelligent Platform Management Interface) for monitoring and control. (Optional) Connect USB 3.0 devices. Maximum USB1-2 power per port is 5W (5V, 1A).
Front Panel LEDs LAN1/2 System HDD1/2 System LED Color State Status Flashing Initializing. White Steady Factory defaults. Blue Steady Device operating nominally. LAN1/2 LEDs Color State Status Steady Link Established at 1/10 Gbps Green Flashing Flashing Indicates Activity HDD1/2 LEDs Color State Status...
Front Panel Buttons Power Reset Button Description Power Press to turn the UniFi Server on or off. There are two methods to reset the UniFi Server to factory defaults: Runtime Reset (Recommended) The UniFi Server should be running after bootup is complete, and the System LED is blue.
Page 7
Front Panel HDD Bays Two 2 TB HDDs are pre-installed. However, they are hot-swappable, so you can replace them at any time if you choose to do so. 1. To replace a pre-installed HDD, press the HDD bay door. 2. Once the door is released, rotate the door and pull the HDD bay out.
Before You Begin Remove the labels that secure the HDD bay doors. 1. Pull the white part of the label. 2. Press the HDD bay door.
Page 9
3. Once the door is released, rotate the door and pull the HDD bay out. 4. Remove the rest of the label. 5. Push the HDD bay back in and close the HDD bay door. 6. Repeat steps 1-5 for the other label.
Hardware Installation The UniFi Server can be placed on a horizontal surface, mounted on a wall, or mounted in a rack. Mounting in a Rack (Optional) 1. Attach the Rack-Mount Brackets to the UniFi Server using the eight Bracket Screws. 2. Attach the UniFi Server to the rack using the four Mounting Screws.
Connecting Power 1. Connect the Power Cord to the Power port of the UniFi Server. 2. Connect the other end of the Power Cord to a power outlet. 3. Press the Power button to turn on the UniFi Server.
Connecting Ethernet 1. Connect an Ethernet cable from your switch to the LAN1 port of the UniFi Server. 2. For an aggregate link, connect another Ethernet cable from your switch to the LAN2 port of the UniFi Server.
Page 13
Connecting VGA 1. (Optional) Connect a VGA cable (not included) from your monitor to the VGA port of the UniFi Server.
Page 14
UniFi Controller or UniFi Video Software The UniFi Controller and UniFi Video software applications are pre-installed on the UniFi Server. Follow these instructions to launch either software: 1. Ensure that your host system is on the same Layer-2 network as the UniFi Server. 2.
Page 15
Configuring the UniFi Server Use SSH and standard Ubuntu commands to configure the UniFi Server. 1. Ensure that your host system is on the same Layer-2 network as the UniFi Server. 2. The UniFi Server is set to DHCP by default, so it will try to automatically obtain an IP address.
Specifications UAS-PRO Dimensions 442.4 x 305.5 x 43.7 mm (17.42 x 12.03 x 1.72") Weight 6.5 kg (14.33 lb) With Mount Brackets 6.6 kg (14.55 lb) Max. Power Consumption Power Method 100-240VAC/50-60 Hz, Universal Input Power Supply 100 to 240VAC, 2 to 4A, 50 to 60 Hz Supported Voltage Range 100 to 240VAC LEDs...
Safety Notices Read, follow, and keep these instructions. Heed all warnings. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm.
Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or (VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation;...
Page 19
No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS’ facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS.
Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING...
Page 21
Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
Industry Canada CAN ICES-3(A)/NMB-3(A) This Class A digital apparatus complies with Canadian ICES-003. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s).
RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter, except as listed for this product’s certification.
Page 24
RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
Page 25
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
[German] Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet. Ελληνική Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει ότι αυτή η συσκευή UBIQUITI NETWORKS, είναι σε συμμόρφωση με τις [Greek] βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας 1995/5/ΕΚ.
Page 27
NETWORKS zariadenie, je v súlade so základnými požiadavkami a [Slovak] ďalšími relevantnými ustanoveniami smernice 1999/5/ES. Español Por medio de la presente UBIQUITI NETWORKS declara que este dispositivo UBIQUITI NETWORKS, cumple con los requisitos [Spanish] esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.