REGISTER YOUR LIFETIME PRODUCT TODAY! There are benefi ts to registering your Lifetime product. With our new online product registration form, it’s fast and easy! Register with us at www.lifetime.com and enjoy these great benefi ts: LIFETIME’S PROMISE TO YOU: Maintaining your privacy is our long-standing policy at Lifetime.
Page 3
BEFORE BEGINNING ASSEMBLY Keep the hardware bags and their contents separate. If any parts are missing, call our Customer Service Department. *TWO ADULTS REQUIRED TO COMPLETE ASSEMBLY* TOOLS REQUIRED FOR THIS ASSEMBLY 8 mm & 10 mm Wrench 2.5 mm Allen Wrench Needle-Nosed Pliers Safety Glasses...
Page 4
ASSEMBLY GUIDES Refer to the following areas throughout the instructions to assist in the assembly process: This area is located at the top, left-hand TOOLS AND HARDWARE REQUIRED FOR THIS PAGE corner of the page and indicates which tools and hardware are needed to complete the assembly steps on a page.
PARTS LIST Item Description Item Description Hinge & Table Top/Back Rest Assembly Hardware Bag Leg & Bench Assembly Hardware Bag PARTS IDENTIFIER PART ILLUSTRATIONS...
Page 6
HARDWARE IDENTIFIER LEG & BENCH ASSEMBLY HARDWARE BAG [CTW] 47 mm 52 mm HINGE & TABLE TOP/BACK REST ASSEMBLY HARDWARE BAG [CTX] *CTT *CTS *CTQ 52 mm 54 mm...
Page 7
LEG & BENCH ASSEMBLY HARDWARE REQUIRED HARDWARE BAG REQUIRED: CTW 47 mm 52 mm PARTS REQUIRED TOOLS REQUIRED HARDWARE BAG REQUIRED: CTW Safety Glasses...
Page 8
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 10 mm (x2) 47 mm Right Leg (CRJ) M6 x 1 x 47 mm Hex-Head Bolts (CSI) Lifetime Logo is on bottom Cross Support (CRL) M6 x 1 Cap Nuts (AON) Tighten Nuts securely, but do not overtighten.
Page 9
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 10 mm (x2) 47 mm **TWO ADULTS REQUIRED FOR THIS STEP** Left Leg (CRI) to Tighten Nuts securely, but do not overtighten. WARNING Bench Assembly (CRK) Align these holes. Cross Bar Location Nub...
Page 10
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 10 mm (x2) 52 mm Tighten Nuts securely, but do not overtighten. Repeat this step for the right side of the Bench Assembly. Left-Most Brace WARNING...
Page 11
HINGE & TABLE TOP/BACK REST ASSEMBLY HARDWARE REQUIRED HARDWARE BAG REQUIRED: CTX *CTT *CTS *CTQ 54 mm 52 mm PARTS REQUIRED TOOLS REQUIRED HARDWARE BAGS REQUIRED: CTW, CTX Needle-Nosed Pliers Safety Glasses...
Page 12
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2” Round Cap Plug (CUK) Metal Tube (CTR) These holes must be aligned...
Page 13
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Adjustment Plate (CTT) Adjustment Fork (CTS) (Fig. 1) (Fig. 2). Fig. 1 Fig. 2...
Page 14
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Adjustment Plate (CTT) Cotter Key (CTU) If necessary, use a pair of pliers or needle-nosed pliers to help insert the Cotter Key.
Page 15
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 8 mm Adjustment Lever (CTQ) #8 x 7/8” Button-Head Screws (CTM) #8 Nylock Nuts (CTL). Repeat sections 2.1 - 2.5 for the other end of the Metal Tube. Align these holes Align these holes and grooves Set Adjustment Fork into the nook on the Legs as shown.
Page 16
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 10 mm (x2) 54 mm M6 x 1 x 54 mm Hex-Head Bolts (CSJ) 1/4” Flat Washers (CTN) more 1/4” Flat Washers (CTN) M6 x 1 Cap Nuts (AON) Repeat this step for the other side of the Metal Tube.
Page 17
TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 10 mm (x2) 52 mm Table Top/Back Rest (CTK) 2.10 Note: These two holes go toward the front as shown. Repeat this step for the other side of the Table 2.11 Top/Back Rest Assembly. WARNING...
Page 18
TABLE-TO-BENCH/BENCH-TO-TABLE CONVERSION Adjustment Lever Adjustment Lever...
Page 20
LIFETIME 2-YEAR LIMITED FACTORY WARRANTY LIFETIME PRODUCTS, INC. RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE. PLEASE INCLUDE YOUR DATED SALES RECEIPT AND PHOTOGRAPHS OF DAMAGED PARTS. REGISTER YOUR PRODUCT FOR QUICKER CUSTOMER SERVICE.