Table of Contents
Advertisement
Quick Links
What's in the box
1 x HR-701L Bluetooth speaker
1 x Users manual
Power
Bluetooth/Play
Pause/Hand-free
+
Volume
Charge HR-701L (rechargeable battery built-in)
1.
Connect to a PC/Laptop/Mac or any 5V USB adaptor with the USB
cable included.
2.
The Red LED will turn ON when charging, and turn OFF when fully
charged.
3.
Unplug the USB cable when fully charged.
Note: The Red LED will flash and makes a sound when the battery power is low
(<21%).
Starting HR-701L Bluetooth Speaker
1.
After fully charged, long press the POWER button to turn on the
speaker.
2.
HR-701L is in standby mode after power-on, blue LED blinks quickly.
3.
HR-701L turn off itself for power-saving purposes if idle for 10 minutes.
4.
Press any button located on top to activate HR-701L from standby
mode.
5.
To manually turn off HR-701L Bluetooth Speaker, press the POWER
button again.
Pairing with Bluetooth enabled devices (Mobile phones/Tablets etc.)
1.
Keep the speaker and device within 1 meter of each other.
2.
Hold down the power button for 2 seconds to turn the speaker on, the LED indicator will blink quickly blue while the
speaker enters search mode.
Start the Bluetooth function on your mobile device and look for "HR-701L" in the Bluetooth device list (depending on
3.
the Bluetooth version of your device you may have to enter pass code „0000‟).
4.
After successfully connecting, the LED will change to solid blue.
Note:
If the pairing was not successful, turn off the speaker and re-pair again.
After successful pairing, paired devices will remember each other so there is no need to pair again unless pairing
information is deleted.
To pair with a new device, just follow steps 1-4 above after un-pairing the existing device.
Pairing HR-701L via NFC function with NFC enabled devices
1.
Turn on HR-701L
2.
Enable NFC and Bluetooth on your phone(NFC settings may be found under your devices' "More/Additional Settings")
3.
Lightly swipe your phone down the NFC logo on side of device, while making minimal contact. The indicator shall turns
solid ON that means successfully paired.
4.
"Compatibility: Most smartphones with NFC running Android 4.1 "Jellybean" and later.
Re-connecting to a paired device
If the speaker does not connect to the last used device automatically, then you will need to select it manually from the list of
devices on your mobile device.
HR-701L Bluetooth Speaker
1 x USB cable
1 x AUX cable
Carry Lanyard
Volume -
Light control
NFC pair area
USB Charge Reset AUX-in
Speaker 1
Subwoofer
Speaker 2
Advertisement
Table of Contents
Related Manuals for PB TEEN HR-701L
Summary of Contents for PB TEEN HR-701L
- Page 1 Hold down the power button for 2 seconds to turn the speaker on, the LED indicator will blink quickly blue while the speaker enters search mode. Start the Bluetooth function on your mobile device and look for “HR-701L” in the Bluetooth device list (depending on the Bluetooth version of your device you may have to enter pass code „0000‟).
- Page 2 Pair HR-701L with a different device First disconnect with existing device by either long pressing the BLUETOOTH or switching off Bluetooth connection of existing device, and then pair with other device according to steps 1-4 above. LED lights control There are 49 LED lights built-in under the grille, you can choose your favorite mode lights by pressing “light control” button...
- Page 3 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Need help?
Do you have a question about the HR-701L and is the answer not in the manual?
Questions and answers