Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TAGSON PS-2/ES
Summary of Contents for TAGSON PS-2/ES
- Page 1 PS-2/ES Automated pack & tag machine with IndES fastening system...
-
Page 2: Table Of Contents
Maintenance Troubleshooting Spare parts list Contact information Technical information PACK & TAG MACHINE TYPE: PS-2/ES Air pressure: 5,5 bar / 80 psi Production year: 2018 Made in Slovenia ( EU ) Distributor: Stular plus Ltd, Koroska cesta 26 4000 Kranj, Slovenia... -
Page 3: Introduction
The main purpose of TAGSON PS-2/ES is to be used in packaging applications. PS-2/ES enables you to pack and tag a wide range of product shapes and sizes. TAGSON automated Pack & Tag machine is designed and made in the EU. -
Page 4: Important Safety Instructions
Important safety instructions This manual contains essential information for the protection of users and others from possible injury and/or equipment damage. Read this manual before using the product, to ensure correct handling, and read the manuals of related apparatus before use. Keep this manual in a safe place for future reference. - Page 5 → Disconnect air supply before attempting to replace any component. → Never and under no circumstances try to apply more than 80 psi (5,5 bar) into the machine. → Do not remove guards and do not operate the machine without having all guards in place. →...
-
Page 6: Ps-2/Es
PS-2/ES (front view) 1 Reel holder for Elastic Staples 2 Screw for adjusting needle gap 3 Ejector rod switch 4 Ejector rod timing adjustment screw 5 Eye protection glass 6 Avery Dennison IndES module 7 Needle adjustment knob 8 Card / product holder... - Page 7 PS-2/ES (back view) 13 Air blow gun 14 Knob for air level pressure 15 Air filter regulator 16 The main air connector 17 Speed adjustments screw 18 Main air valve ON/OFF for the air supply...
-
Page 8: Unpacking The Machine
Unpacking the machine 1. Check the contents of the PS-2/ES shipping box. It should contain the following: → One PS-2/ES machine → One reel holder → One safety and manual instruction book for PS-2/ES → One safety and manual instruction book IndES Avery Dennison fastening system →... -
Page 9: Installation Of Air Supply
Installation of air supply WARNING! Turn off air supply before beginning installation. Before the first use: → Read safety and manual instructions. → Close main air valve on the machine before connecting air supply. → Install air supply hose and open main air valve on the machine. -
Page 10: Indes Avery Dennison Module
IndES Avery Dennison Fastening System module. Working with the machine This chapter explains how to operate the Tagson Pack & Tag machine. NOTE: Before operating, please check the air supply level. Air supply must be 80psi (5,5 bar). WARNING! Always turn off air supply whenever the unit is not in use, or when servicing the machine. - Page 11 5. Push the other side also down until the bottom rung is also engaged with the anti-back. → Both sides of the staple should be aligned. 6. Holding the staple chain with both hands, pull up gently to ensure that the chain is engaged with the feed.
- Page 12 3. ADJUSTMENT FOR SINGLE OR DOUBLE SHOT OPERATION With staple loaded in the Module Assembly: Air Supply must be ON 1. Locate the Single Shot mode/Double Shot mode screws on the Module’s Feed Systems. 2. Move the screws to the “I” for Single Shot mode or “II” for Double Shot mode: →...
-
Page 13: Before Use
5. ADJUSTING LASER MARKER Tagson PS-2/ES machine has two laser markers installed on the IndES module. With laser markers you can point where needles hit cards. → Turn off air supply with the Main switch → Install the card with product under the machine. -
Page 14: Maintenance
0.5 sec. Maintenance This chapter explains the routine maintenance of the Tagson Pack & Tag machine and its spare parts replacement. After finishing, always clear the machine with the air blow gun , especially on the needle plate WARNING! Prior to any maintenance, replacement or repair, air supply must be switched off. -
Page 15: Troubleshooting
Trouble shooting This chapter describes symptoms, possible causes and solutions to problems one may encounter when operating the Tagson tagging machine. Symptom Cause Action Fastener breaking on insertion or Staple size too small Use larger staple size Fastener not inserted correctly... -
Page 16: Spare Parts List
Spare parts list The spare parts list only applies to the Tagson PS-2 machine without the IndES module. For the IndES module spare parts list, please see the original safety and manual instruction book IndES Avery Dennison fastening system. Item...