Simplicity 1694847 Parts Manual page 25

Auger Housing and Chute Group - 24, 28 & 32 inch
REF NO PART NO.
1 1931333
2 2860210
4 1960686
5 1670578
6 1704161C
6 1720671C
7 1706085
8 1960001
9 1667865
10 1666613
11 1702219
12 1960126
13 1611945
14 1611939
15 2825094
16 1720446
17 1611989
18 1719140
19 1719139
20 1719138
21 1960600
22 1726411A
23 1960738
25 1665982A
26 1729578
27 1930659
28 1663189
29 1665980
30 1668639C
31 1923325
32 1960687
33 1727854C
34 1709946A
34 1709947A
34 1709948A
35 1935048
36 1960711
37 1931277
38 1960699
39 1960684
40 1664847
41 1729642C
Footnotes
The above parts group applies to the following Mfg. Nos.:
1694847 - 10560E
1694848 - 10560EX
1694849 - 11570E
1694850 - E11570
1694851 - 1380E
1694852 - E1380
© Copyright 2005 Simplicity Manufacturing, Inc. All Rights Reserved.
QTY. DESCRIPTION
1 CARRIAGE BOLT, 5/16-18 x 3/4 G5
1 WASHER, Nylon
1 NUT, Hex Flange ESNA Light, 5/16-18 (Used on all models Except 24 in. Models)
1 KNOB, Internal Thread, 5/16 (Used Only on 24 in. Models)
1 CHUTE AND DEFLECTOR ASSEMBLY, Manual (Used Only on 24 in. Models)
1 CHUTE AND DEFLECTOR ASSEMBLY, w/Remote (Used on all models Except 24 in.
Models)
2 DECAL, Orange Strip
3 SCREW, Hex Washer Head Pastite, 10-14 x 5/8
3 SPRING, Flat
3 HOLD DOWN, Chute
3 SPACER, 17/64 ID x 3/8 OD
2 NUT, Push 1/4
1 ROD, Spring
1 SPRING, Compression
1 TIE, Self Locking (Used on all models Except 24 in. Models)
1 CABLE AND KNOB ASSEMBLY, Chute (Includes Ref. No. 17, 18, 19, 20 & 21)
1 BOOT, Bellows
1 COLLET
1 SEAL, Rod
1 KNOB
1 SCREW, 8-32
1 BRACKET, Cable
3 CAPSCREW, Hex Head, 5/16-18 x 5/8 G5
1 RETAINER, Bearing
1 BEARING, Ball
3 NUT, Retainer Speed, 5/16-18
2 SPACER, Low
1 BEARING, Flange
2 CAP, Bearing, 3-3/4OD
6 CAPSCREW, Hex Head 5/16-18 x 7/8 G5
6 NUT, Hex Flange 3/8-16 ESNA
2 SKID SHOE, Reversible
1 BLADE, Scraper, 24 in.
1 BLADE, Scraper, 28 in.
1 BLADE, Scraper, 32 in.
5 NUT, Hex Flange, 5/16-18, Two-Way Lock GA (Quantity 7 Only on 32 in. Models)
4 CARRIAGE BOLT, 3/8-16 x 3/4
6 NUT, Hex Flange, 5/16-18
5 CARRIAGE BOLT, 5/16-18 x 5/8 G5 (Quantity 7 Only on 32 in. Models)
4 NUT, Hex Keps, 5/16-18, Conical Washer (Used on all models Except 24 in. Models)
2 CAPSCREW, Hex Head, 5/16-18 x 3/4 G5 (Used on all models Except 24 in. Models)
2 CUTTER, Drift, 1/4 in. Thick, 20LG (Used on all models Except 24 in. Models)
1694867 - 9560E
1694914 - 9560EX
25
TP 400-4250-00-LW-S