Related Manuals for BestWater Jungbrunnen 25-00
Summary of Contents for BestWater Jungbrunnen 25-00
- Page 1 InSTRUCTIOn mAnUAL WATER-DISTRIBUTOR JUngBRUnnEn 25-00 WITh REvERSE OSmOSIS SySTEm...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Page BEFORE YOU INSTALL THE WATER DISTRIBUTOR SAFETY ISSUES BASIC WATER DISTRIBUTOR CW-929 ELEMENTS OPERATING FUNCTIONS OF WATER DISTRIBUTOR EQUIPPED WITH AN RO SYSTEM 4.1 Water filtration 4.2 Tank filling 4.3 Water cooling system Flow restrictor WATER DISTRIBUTOR BASIC TECHNICAL PARAMETERS INSTALLATION SCHEMES 6.1 Water installation scheme Electrical installation scheme... - Page 5 1. Water level indicator Water level indicator 9. Cooling system condenser 2. Control panel Control panel 10. Water drainage for tanks 3. Hot water tap water tap 12. Regfrigerator compressor 4. Cool water tap 13. Waste water connection 5. Cold Cold water tap water tap...
- Page 6 1. Top cover 2. Outer plate of warm water tank 4. Steam outlet opening 5. Steam outlet cover 6. Hot water tank 7. Cool water tank 8. Hydraulic floating valve...
-
Page 7: Tank Filling
GRANULAR ACTIVATED CARBON POSTFILTER - fourth level of filtration F iltered water goes through the granular activated carbon postfilter, which improves water taste and smell. Optional: MINERALISING POSTFIL TER - fifth level of filtration After the fourth level of filtration water goes through the mineralising postfilter, which saturates water with mineral salt ions. - Page 9 Cooling...
-
Page 10: Electrical Installation Scheme
ELECTRICAL INSTALLATION SCHEME. r-- - · -- r2ßJ_ : � : � - ! i • ZL21, -;i • .-.230vf50.Hzi �-- -----· - --· L _________ _ Electrical scheme Eie ctrovalve Low pressure switch Float i ng valve with a switch Power supply socket - Voltage -230 V;... -
Page 11: Useful Installation Tips
USEFUL INSTALLATION TIPS In case of when Water Distributor contains QC-type connections (quick connections) it is sufficient enough to push in the installation tubes into every QC frtting. Standard QC push-in fitting installation. Push in hard the tube in the frtting. Locking clips prevent the tube from slipping out and the inner rubber gasket assures perfect sealing. -
Page 12: Method 2: 3/8" Or 1/2" Water Feeder- Installation At Water Inlet
Unscrew the compression nuts and remove the faucet. Put the rubber gaskets and install connector elements, remembering that the element with a hole should be mounted on the main cold water inlet. Tighten firmly. Screw in the ball valve into the water connector element. 1 nstall the faucet elements to water feeder. -
Page 13: Pressure Control And System Rinsing
Drill a 0 6 mm hole in the location marked in point 8.2.2 into the drain pipe and clean the surface of the pipe. Remove the paper protection and round inner part from the foam gasket that is included in the set. Stick it to the drain pipe exactly in the place where the hole in gasket covers the hole in the pipe. -
Page 14: Water Distributor Operation Conditions
9. WATER DISTRIBUTOR OPERATION CONDITIONS llJI PRECAUTIONS Mal<e sure that lhe space Oo notlnstall the dlstritutor ct>se to BllY between the wall and distributa- soorces heat places exposed to 9.Jn not pour coffee. tea. milk or any similarliquids into the water tank. Keep away from cHldren Make sure that the water distributor is connectoed to the pcr N er source of a... -
Page 15: Water Distributor Service And Maintenance
2. Press "REBOIL" to heat water. At this moment the light will change from "KEEP WARM" to ,,HEATING". 3. In order to cool water first press the cold water button lever and then "COLD POWER" button. CAUTION: lf it is not necessary, do not press "COLD POWER"... -
Page 16: Membrane Exchange
In order to exchange the prefilters, follow the instructions given below: Cut off water supply by tuming the ball valve located on the water supply to the close position. Unplug the \/Vater Distributor. Leave the system for 3-5 minutes in order to lower the pressure to the minimum. Unscrew the prefilters to the left (counterdockwise). -
Page 17: Postfilters Exchange
PUT THE MEMBRANE INSIDE THE HOUSING ALWAYS IN THE DIRECTION POINTED ON THE ABOVE SCHEME � iI!I] POSTFIL TERS EXCHANGE Fellow the instruction given below in order to exchange the postfilters: Cut off water supply by turning the ball valve located on the water supply to close position Leave the system for 3-5 minutes in order to lower the pressure to the minimum Unscrew the postfilters to the left (counterclockwise).
Need help?
Do you have a question about the Jungbrunnen 25-00 and is the answer not in the manual?
Questions and answers