Advertisement
Quick Links
Advertisement
Related Manuals for TPP Turbo-Fix
Summary of Contents for TPP Turbo-Fix
- Page 1 TPP Pipettor Turbo-Fix Operating instructions 155923_V13...
- Page 2 Declaration of conformity TPP Techno Plastic Products AG – 8219 Trasadingen, Switzerland declares on its own responsibility that the devices Description Models TPP Pipettor Turbo-Fix 94700, 94701, 94702 comply with: EU Directives (DoW: Date of Withdrawal) Before DoW After DoW...
-
Page 3: Table Of Contents
TPP Techno Plastic Products AG CH-8219 Trasadingen, Switzerland T +41 52 687 01 87 F +41 52 687 01 77 info@tpp.ch www.tpp.ch Customer service Please contact your local TPP Techno Plastic Products AG representative, see www.tpp.ch or contact info@tpp.ch. www.tpp.ch... -
Page 4: Introduction
Safety notes 1) Do not use or charge TPP Pipettor Turbo-Fix in an atmosphere with danger of explosion. Also, do not pipette highly flammable liquids such as acetone or ether. 2) When handling dangerous substances, comply with the material safety data sheet (MSDS) and with all safety guidelines such as the use of protective clothing and safety goggles. -
Page 5: Description Of The Device
TPP Pipettor Turbo-Fix - Operating instructions V13 Description of the device Description of the device Scope of delivery • TPP Pipettor Turbo-Fix device • 1 rechargeable Li-ion battery • Mains adapter • Wall mount • Hydrophobic sterile filter 0,45 µm (spare) •... -
Page 6: Installation
Installation Charging the battery A full charge takes 3.5 hours. Before the first use, TPP Pipettor Turbo-Fix should be charged until the battery charge indicator (4) turns green, showing that the battery is full. When the battery charge indicator (4) starts flashing red, TPP Pipettor Turbo-Fix can be used for around 100 pipetting cycles before shutting down. -
Page 7: Operation
“to deliver” (TD) pipettes that are not of the “blow-out” type (blow-out pipettes have two thin rings or a frosted band around the neck). TPP Pipettor Turbo-Fix is featured with a “TURBO” mode. Plug the mains adapter cable into the pipette controller and turn the thumb wheel completely to the right for maximal speed. - Page 8 TPP Pipettor Turbo-Fix – Operating instructions V13 Operation TPP Techno Plastic Products AG...
- Page 9 TPP Pipettor Turbo-Fix – Operating instructions V13 Operation www.tpp.ch...
-
Page 10: Maintenance
TPP Pipettor Turbo-Fix: liquid should not leak out of a filled pipette before the dispensing button is pressed. Cleaning and servicing TPP Pipettor Turbo-Fix can be cleaned with a cloth moistened with soapy water or with a 70 % ethanol. Disassembly of the nose piece: Unscrew the nose piece (7) from the handle by turning it counter clockwise. -
Page 11: Technical Data
Storage: -10–50°C, max. 95% RH Chemical compatibility The table below lists TPP Pipettor Turbo-Fix parts that come into contact with the aspirated liquid or its aerosols and vapors, and rates the compatibility of these parts to a few of the chemicals commonly used in laboratories. To determine the compatibility of a component to a chemical not listed in the table, please consult one of the several tables available on the internet. -
Page 12: Spare Parts
TPP Pipettor Turbo-Fix - Operating instructions V13 Spare parts Chemical compatibility chart Parts Materials Handle Nose piece housing Pipette mount, Silicone Filter rubber, tubings Internal parts (e. g. pump) Metal Compatibility ratings: A = Good: no or minor effects. B = Fair: moderate effects, not recommended for continuous use.
Need help?
Do you have a question about the Turbo-Fix and is the answer not in the manual?
Questions and answers