Do you have a question about the BBC-270 and is the answer not in the manual?
Questions and answers
Carol
July 23, 2025
Why our bidet stopped working?? Our bidet started slowing down for about a month or two and now it's not working at all. Our water pressure is completely fine and everything was cleaned properly and we've had our bidet for about 5 years and now it doesn't work. What could it possibly be???
Page 2
Dimensions ......Page 4 PRODUCT INSTALLATION Pre Installation ....... Page 5 Installing the Bidet Attachment ..Page 5 PRODUCT OPERATION How to use the BBC-270 ....Page 9 MAINTENANCE Cleaning ......Page 9 Short Term Non-Use ....Page 9 Warranty ......Page 10 CONTACT .
Page 3
PRODUCT INFORMATION • High-quality ABS material with full body panel • Premium quality with all metal inlet and installation parts • Dual Nozzle with self-cleaning • Continuous warm water • Adjustable water pressure • Adjustable water temperature • Cold water bypass •...
Page 4
Bidet attachment with control knob > Protective 0-ri ngs 3/8'' T Valve - Hot 7 /8" T Valve - Cold White Washer 78. 7inch hot water hose 25.5inch cold water hose...
Page 5
PRODUCT INFORMATION MENSIONS 3 . 51 � C, 0 • ") • 1 7. 3 0 � � c :> Jiil � • CV') ..� " � CV') " - II I • C"1 �...
Page 6
If you do not have access to the fill valve under the toilet tank,contact Biobidet Customer Service at 84 7 .458.2334 and we may be able to provide alternative fittings.
Page 7
PRODUCT INSTALLATION (cont.) INSiTALLING BBC-2�0 (cont.) 2.Close the water supply valve and flush the toilet completely so that there is little to no water left in the toilet tank. Step 2 3.Disconnect the water hose from underneath the toilet tank. Step 3 4.Connect the 7/8"T-valve to the toilet fill valve where you just removed the water hose.
Page 8
PRODUCT INSTALLATION (cont.) ffihlli BBC-2� (colilt.} INSniALLl�G 6.Connect the 25.5 metal hose we supplied to the open side of the T-valve. step 6 7.To install the hot water line,close the water supply sink valves underneath your sink. step 7 8.Disconnect the water hose from your sin k's hot water suppy valve.
Page 9
PRODUCT INSTALLATION (cont.) INSTALLING THE BBC-270 (cont.) 10.Attach the water supply hose that comes from the water shut off to the top of the T-valve. step 10 11.Connect the78.7" metal hose we supplied to the open side off the T-valve.
Page 10
15 16. If there are no immediate leaks, check again in about 5-10 minutes and your BBC-270 is ready for use! Note: If any leaks occur, check all rubber washers and make sure all connections are tight and secure.If...
Page 11
• Clean the BBC-270 by wiping the surface area with a damp cloth reg ularly. • Do not use harsh detergents or any cleaning tools with bristles on your bidet. Steam cleaning is the preferred cleaning method for your bidet. For a deep, chemical free clean, consider the BioMist Bidet Cleaner.
Page 12
arranty Your Bio Bidet is warranted against defects in materials or workmanship for one (1) year from the Date of original purchase. Defective parts or a defective product returned to Bio Bidet will be repaired with new or comparable rebuilt parts or exchanged for a Refurbished Bio Bidet as determined by Bio Bidet in their sole discretion This limited warranty given by Bio Bidet covers all...
Page 13
Technical Support /Customer Service Bio Bidet 7900 S Route 31 Crystal Lake IL 60014 T :847.458.2334 U.S TOLL FREE :877.339.5214 support@biobidet.com www.biobidet.com...
Need help?
Do you have a question about the BBC-270 and is the answer not in the manual?
Questions and answers
Why our bidet stopped working?? Our bidet started slowing down for about a month or two and now it's not working at all. Our water pressure is completely fine and everything was cleaned properly and we've had our bidet for about 5 years and now it doesn't work. What could it possibly be???