Advertisement
Quick Links
I N S T A L L A T I O N A N D
U S E R I N S T R U C T I O N S
MODELS
INFINITE RANGE OF ELECTRIC FIRES
LFE600GF – FLE800GF/2/3 – LFE1032GF/2/3 – LFE1500GF/2/3 – LFE1800GF/2/3
PLEASE NOTE
This appliance is not intended to be used as a primary source of heating.
Running the Heating element continuously is not recommended.
Once installed, the installer should take the appropriate steps to ensure that the
user understands how the appliance operates and should make the customer
aware of the appliance's basic service requirements.
Advertisement
Related Manuals for Living Fire INFINITE SERIES
Summary of Contents for Living Fire INFINITE SERIES
- Page 1 I N S T A L L A T I O N A N D U S E R I N S T R U C T I O N S MODELS INFINITE RANGE OF ELECTRIC FIRES LFE600GF – FLE800GF/2/3 – LFE1032GF/2/3 – LFE1500GF/2/3 – LFE1800GF/2/3 PLEASE NOTE This appliance is not intended to be used as a primary source of heating.
-
Page 2: General Warnings
Please read these instructions before installation or use and keep this booklet handy for future reference. SAFETY This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the applicance by a person responsible for their safety. - Page 3 If the supply cord is damaged, a special cord assembly available from the manufacturer or its service agent must replace it. Please contact Living Fire and reference (Insert CAT number – Do not have yet) to request a new lead.
-
Page 4: Installation Requirements
INSTALLATION REQUIREMENTS BUILT IN MODELS This product has been designed to be installed into a studwork or existing chimney breast. Please note that any GF2 models from the LFE series range are not suitable to be installed into an existing chimney breast. Please seek advice from an authorised person, with reference to the structural integrity of the installation site. - Page 5 STUDWORK / INSTALLATION METHOD All LFE Series products require an external aeration clearance of 100mm directly above and below the main product casing. (Failing to do so can cause issues with the heat and flame function). • Each LFE series product comes complete with one or more wall mounting brackets. •...
- Page 6 1 GLASS FRONTED MINIMUM OPENING SIZES REQUIRED (MM) 600 GF 638.00 195.00 638.00 800 GF 852.00 316.00 790.00 1032 GF 1,061.00 315.00 556.00 1500 GF 1,563.00 315.00 556.00 1800 GF 1,802.00 315.00 610.00 2 TWO SIDED GLASS (LEFT) MINIMUM OPENING SIZES REQUIRED (MM) 800 GF2 L 841.00 316.00...
-
Page 7: Front Glass Removal
FRONT GLASS REMOVAL To remove the front glass and install the log set. The below steps must be taken. Remove the two screws located in the Remove the bottom glass retaining bar. bottom glass retaining bar. Remove the glass by pulling the second retaining Place the log set as stated and replace the glass bar away from the body of the fire. - Page 8 CONTINENTAL LOG SET LAYOUTS: LFE SERIES Each LFE1800GF–2–3 / LFE1500GF–2–3 / LFE1032GF–2–3 / LFE800GF–2–3 / LFE600GF comes as standard with a continental log set. Please note that the log styles and sizes will vary dependent on model. The images shown are examples of suggested fuel/log set layouts. The log set layout can be arranged to personal preference.
-
Page 9: Wall Mounted
PLINTH INSTALLATION It is advised that the plinth is installed to the product before installation. WALL MOUNTED In order to install the plinth to the LFE product please follow the following steps: Screw and fix the grey brackets provided to the front and sides of the LFE product using the shortest side of the bracket. - Page 10 Call Out by our appointed engineer. This Warranty is in addition to and does not affect the purchaser’s statutory rights of consumers. Living Fire Pty Ltd 361 Swan Street Richmond Vic 3121 T +61 3 99 777 888 E info@livingfire.com.au...
- Page 11 D I F F E R E N T B Y D E S I G N...