Subscribe to Our Youtube Channel
Related Manuals for IXXAT CAN Series
Summary of Contents for IXXAT CAN Series
- Page 1 CAN FD Repeater CAN-CR100, CAN-CR110/FO, CAN-CR120/HV, CAN-CR300 USER MANUAL 4.01.0210.20000 1.1 ENGLISH...
- Page 2 Important User Information Liability Every care has been taken in the preparation of this document. Please inform HMS Industrial Networks of any inac- curacies or omissions. The data and illustrations found in this document are not binding. We, HMS Industrial Net- works, reserve the right to modify our products in line with our policy of continuous product development.
-
Page 3: Table Of Contents
Table of Contents Page User Guide ........................3 Document History ......................3 Trademark Information ....................3 Conventions ........................4 Safety Instructions......................5 Information on EMC .......................5 General Safety Instructions.....................5 Scope of Delivery ......................5 Product Description ....................... 6 Configuration ........................7 Configuring the Lock Time ....................7 Extending the Recessive Bit ...................7 Installation ........................ - Page 4 This page intentionally left blank...
-
Page 5: User Guide
February 2018 First release February 2018 Minor corrections Trademark Information IXXAT ® is a registered trademark of HMS Industrial Networks. All other trademarks mentioned in this document are the property of their respective holders. CAN FD Repeater User Manual 4.01.0210.20000 1.1... -
Page 6: Conventions
User Guide 4 (18) Conventions Instructions and results are structured as follows: ► instruction 1 ► instruction 2 ➨ result 1 ➨ result 2 Lists are structured as follows: • item 1 • item 2 Bold typeface indicates interactive parts such as connectors and switches on the hardware, or menus and buttons in a graphical user interface. -
Page 7: Safety Instructions
Safety Instructions 5 (18) Safety Instructions Information on EMC Risk of interference to radio and television if used in office or home environment! Make sure, that DIN rail is connected to ground. Use exclusively included accessories. Make sure, that shield of CAN cable is connected. Use exclusively shielded cables. -
Page 8: Product Description
Product Description 6 (18) Product Description CAN-CR100 • 2 x CAN/CAN FD interfaces • CAN according to ISO 11898-2 • ISO CAN FD and nonISO CAN FD • CU channels • variant with integrated bus termination resistor and variant without bus termination resistor available •... -
Page 9: Configuration
Configuration 7 (18) Configuration To operate the CAN repeater no software installation is required. The CAN repeater is configured via DIP switches (1). Fig. 1 DIP switches Configuring the Lock Time The lock time is used to avoid bit errors caused by signal propagation delay. ►... -
Page 10: Installation
Installation 8 (18) Installation Mounting the Device Fig. 2 Mounting on DIN rail ► Make sure that the lock time is configured (see Configuration, p. ► Make sure, that the device is not connected to power supply. ► Hook the device onto the upper lip of the rail and push downwards (1). ►... - Page 11 Installation 9 (18) 6.2.1 Power Connector Pin Allocation Pin no. Signal +9 V to +36 V DC — — 6.2.2 CAN Connector Pin Allocation Pin no. Signal CAN high CAN low CAN GND Shield If a D-Sub 9 connector is used, observe the following pin allocation of the D-Sub 9 connector. Pin no.
-
Page 12: Operation
Operation 10 (18) Operation LEDs 1 2 3 Fig. 4 LED array LEDs PWR 2/3/4 do not have any function. The LEDs CAN 3/4 are activated only with CAN-CR300. 7.1.1 Power LED Power LED PWR 1 indicates the status of the power supply. LED state Description Comments... -
Page 13: Additional Components
Additional Components 11 (18) Additional Components Glass Fiber Cable Fig. 5 Glass fiber cables FSMA and ST HMS Industrial Networks offers cable assemblies (FSMA, ST) in various lengths to connect two CAN-CR110/FO. CAN FD Repeater User Manual 4.01.0210.20000 1.1... -
Page 14: Technical Data
Technical Data 12 (18) Technical Data Weight Approx. 150 g Operating temperature -20 °C to +70 °C Storage temperature -40 °C to + 85 °C Power supply +9 V to +36 V DC Housing material Polyamid CAN/CAN FD transceiver Microchip MCP2562FD CAN bus termination resistor 120 Ohm (only with variants with integrated bus termination resistor) CAN baud rates... -
Page 15: Support/Return Hardware
• updates 10.1 Support ► For problems or support with the product request support at www.ixxat.com/support. ► If required use support phone contacts on www.ixxat.com. 10.2 Return Hardware ► Fill in the form for warranty claims and repair on www.ixxat.com. - Page 16 This page intentionally left blank...
-
Page 17: A Regulatory Compliance
EMC Compliance (CE) The product is in compliance with the Electromagnetic Compatibility Directive. More information and the Declaration of Conformity is found at www.ixxat.com. FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: •... -
Page 18: Rohs Directive
Appendix A: Regulatory Compliance 16 (18) RoHs Directive The product is in compliance with the RoHs Directive 2002/95/EC (Restriction of the use of cer- tain hazardous substances in electrical and electronic equipment). Disposal and recycling You must dispose of this product properly according to local laws and regulations. Because this product contains electronic components, it must be disposed of separately from household waste. - Page 19 This page intentionally left blank...
- Page 20 last page © 2018 HMS Industrial Networks AB Box 4126 300 04 Halmstad, Sweden info@hms.se 4.01.0210.20000 1.1.7384 / 2018-02-08...
Need help?
Do you have a question about the CAN Series and is the answer not in the manual?
Questions and answers