Optex UC1-CL11 Instruction Manual

CC-Link Communication Unit
UC1-CL11
Instruction Manual
●Thank you for purchasing this product. Before using this product, confirm that the
product you have received is the product that you requested.
●Read this instruction manual thoroughly before use, and keep it in a safe location.
Indicates that incorrect use may lead to a hazard-
ous situation resulting in injury or death. Also indi-
Warning
cates a risk of significant property damage.
●This product is not explosion-proof and should not be used around flammable or explosive gases or liquids.
●Doing so may cause injury, fire, or electric shock. This product cannot be used as protective equipment
for the purpose of protecting the human body.
●It is dangerous to wire or attach/remove the connector while the power is on. Make sure to turn off the
power before operation.
●Installing in the following locations may result in malfunction:
1. Dusty or steamy locations.
2. Locations where corrosive gas is generated.
●The product is not designed for outdoor use.
●Do not wire with high voltage cables or power lines. Doing so may cause malfunction or damage by
induction.
●Detection characteristics may vary depending on the state of the target object and variations among
individual products.
●Do not use the product in water.
●Do not disassemble, repair, or modify this product. Doing so may cause injury, fire, or electric shock.
●Operate within the rated ranges.
Included accessories
Please confirm that the following accessories are included in the box.
• UC1-CL11 • This instruction manual
CC-Link connector External power connector
Names of parts
1
2
7
Number Name
(1)
DIN rail mounting tabs Tabs for securing the unit to a DIN rail.
(2) CC-Link connector Connector for connecting a dedicated CC-Link cable.
(3)
LED display area Displays the unit status or the communication status.
(4) Baud rate setting switch Sets the baud rate for CC-Link communication.
0: 156 kbps (initial value)
1: 625 kbps
2: 2.5 Mbps
(5) S t a t i o n n u m b e r s e t t i n g Sets the station number of the unit on the CC-Link network.
switch The settable range is from 01 to 64 (with 01 set as the initial
value).
× 10:
disabled)
× 1: Ones digit of the station number
(6) External power connector Connects to an external power source.
(7) Interconnection connector Connects to supported devices.
Ramco National
Warning
Caution
3. Locations with direct exposure to water or oil
splashes.
4. Locations where heavy vibrations or impacts
may occur.
• End plates (2)
Terminating resistor (110 Ω )
110 1/2 W
(Brown-Brown-Brown-Gold)
3
4
5
6
Explanation
3: 5 Mbps
4: 10 Mbps
5 to 9: Disabled
Tens digit of the station number (7 through 9
800-280-6933 | nsales@ramcoi.com

Specifications

Model
CC-Link specifi- CC-Link version
cations
2/3/4 (switches automatically according to no. of connected units)
No. of occupied stations
Station type
Baud rate 156 kbps
Overall length 1,200 m
D3RF-○○○
No. of connectable
units
Power indicator (green), Status indicator (green), Communi-
Indicators
Switches Station number setting
Communication speed
Interconnection connector type
Power rating Power supply voltage
Current consumption
E n v i r o n m e n t a l Protection circuit
resistance Protection category
Operating temperature/ -25 to +55°C/35 to 85%RH (no condensation or freezing)
humidity
Storage temperature/ -40 to +70°C/35 to 95%RH (no condensation or freezing)
humidity
Vibration resistance
Shock resistance
EMC compliant (2004/108/EC); RoHS compliant (2011/65/EU)
Applicable regulations
Applicable standards
Material
Weight Main unit: Approx. 90 g (incl. connector); Packaged: Approx. 155 g
*The maximum number of connectable units varies according to the operating temperature.
Operating temperature (°C) -25 to 55°C
No. of connectable D3RF-○○ units 1 to 3
Dimensions
39
16.21 22.1
Indicators CC-Link connector
10.65
Baud rate
setting switch
Station
number
setting switch
Interconnection
connector
External power connector
2.8 12.4
Installation and connection
●
Installing to DIN rail
Install the unit to the DIN rail, and in the same way, install the fiber amps and connect them.
NOT E
Remove the power cable before proceeding with installation. In particular, make sure there is no
power being transmitted when connecting and disconnecting fiber amps to and from the unit.
● Align the DIN rail mounting tabs on the lower part of the back of the unit with the bottom of
the DIN rail, and while pushing against the DIN rail in the direction indicated in (1) below,
set the unit onto the rail as indicated in (2).
② Mount
Frame Grounld(F.G.)
DIN rail
③
Unmount
① Push to DIN rail
DIN rail mount tab
NOT E
To remove the unit from the DIN rail, push the unit against the DIN rail in the direction indicated in
(1) above, and pull in the direction indicated in (3).
● Mount the fiber amps on the DIN rail in the same way, and connect them to the unit.
connector
Interconnection connector
UC1-CL11
Ver. 1.10
Remote device station
625 kbps 2.5 Mbps 5 Mbps 10 Mbps
600 m 150 m 100 m
200 m
Up to 16 units
cation indicator (green),
Error indicator (red)
0 to 9 rotary switch × 2
0 to 9 rotary switch × 1
Dedicated 5-pin connector
12 to 24 VDC, including ±10% ripple (p-p)
160 mA or less (at 12 V)
Reverse connection protection
IP50
10 to 55 Hz; double amplitude 1.5 mm;
2 hours in each of the X, Y, and Z directions
Approx. 50 G (500 m/s ), 3 times in each X, Y, and
2
Z direction
EN 61000-6-2, EN 55011 (Group 1, Class A )
Polycarbonate
-25 to 50°C -25 to 45°C
4 to 8 9 to 16
N OT E
When mount on DIN rail is not correct, problem
of connection with sensor of F.G. happens.
Confirm DIN rail mount tab are locked and
mount rightly.
www.Optex-Ramco.com
ポイン
When co
leftmost
connecto
interconn
D3RF (Ma
●
Attach end
The tighte
Orient the
the left an
the DIN ra
②
●
Wirin
This section ex
• Make sure the
• Use recomme
• Refer to the C
ner Association
● Connect th
a pin term
● Plug the C
The tighte
N OT
To remov
the cable
hole.
●
Attaching a
If this u
nect a t
●
Conn
This unit operat
In addition, this
section explains