CEBEK TL-10 Manual

E L E C T R O N I C C I R C U I T S
2 CHANNELS FLIP-FLOP RECEIVER REMOTE CONTROL
The TL-8 is a 2 channels remote control flip-flop receiver supplied by 230 VAC with relay output working by radio-
frequency. It will recognize the signal from TL-5 or TL-6 emitters, verify the security code and maintain the output
connected until you stop to press the push button of the emitter.
You could configure your own security code (between 13.122 possibilities) as well as to work with the TL-5 or the TL-6
Cebek emitters. It includes micro-switches to select the code, antenna output, led and acoustic signal for the
output as well as connection terminals.
TECHNICAL CHARACTERISTICS.
Voltage. ..............................................................................................230 V. AC.
Minimum Consumption. ....................................................................20 mA.
Maximum Consumption. ...................................................................110 mA.
Operating Frequency. .........................................................................433.92 Mhz.
Maximum Reach (approximately) . .....................................................20 - 30 m.
Maximum Load at Output. ................................................................3 A.
OPERATING.
MODULE'S SUPPLYING. The Circuit TL-10 had to be supplied by 230 VAC. Using an adequate plug and a cable for
mains connect this last one to the input terminal 230 VAC. Install a fuse and a switch as it is indicated in General
Wiring Map (see hereafter). Both are necessary to protect the module and for your own security, as it is indicated
in EEC regulations. Then, verify that you have correctly connected the module.
Before to connect the module to the mains inserting voltage, please do the rest of connections specified
hereafter. Do not forget that in several part of the module there is voltage (230 VAC), for this reason we suggest
you to be carreful.
OPERATING. All CEBEK remote control works with a frequency adjusted at 433.92 MHz. For this reason, the TL-10
module includes micro-switches (SW-1) allowing to configure a security code between 13.122 possibilities, for
each module. Then, your module will be different from others, even if they offer same characteristics.
Seeing the drawing Nº1, you could note that the micro-switches SW-1 have 8 switches with three different positions. "-
", "0" and "+". You have to modify the switches position that you have received in order to select you personal code.
Do not forget. The receiver and emitter have to have the same code.
configurated with the same code, you could supply the module. Then, press the push button on the emitter and
the corresponding output will be connected till you press again the button, to disconnect the output.
ANTENNA INSTALLATION. To obtain a maximum and clear reception, you have to install an exterior antenna.
Seeing the paragraph "General Wiring map", install a metallic antenna with a length of 130 mm. The cable
between antenna and module had to be shielded and inferior than 25 cm. Connect the negative terminal to
the ground.
OUTPUT CONFIGURATION. Even if the receiver TL-10 have been developed to control its corresponding emitter
with 2 channels (TL-6 module), it also could be controlled by the TL-5 module. 1 Channel emitter. Then, you have
to select between two push buttons the wished receiver output.
From the factory, the module is supplied to be controlled by the TL-6 module (with JP1 Jumper closed). To control the
TL-10 thanks to the TL-5 module, you have to select which output will be connected after to press the push button.
Then, you have to remove the "JP" piece of the JP1 Jumper and with it closed the JP2 jumper. Selecting one of two
jumpers, you could select the required output.
JP
Piece
Jumper no Closed
(Open).
1
TL-10 TL-10
Once emitter and reciver are
1 2 3 4 5 6 7 8
+
Fig. 1.
0
-
Closed
JP
Jumper
SW-1