Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Wassermann Dental-Maschinen WSM-2
Summary of Contents for Wassermann Dental-Maschinen WSM-2
- Page 1 Polishing motor WSM-2 USER MANUAL...
- Page 2 Keep this user manual in a safe place where it can be referred to as required at any time. Company address: Wassermann Dental-Maschinen GmbH Rudorffweg 15-17 D-21031 Hamburg, Germany Phone. : +49 (0)40 / 730 926 – 0 Fax.: +49 (0)40 / 730 37 24 E-mail: info@wassermann-dental.com...
-
Page 3: Table Of Contents
Contents 1 Features..........................4 2 Safety guidelines........................4 2.1 Safety symbols used in this manual................4 2.2 Safety guidelines......................5 2.3 Responsibility for operation or damage...............5 3 Application..........................5 4 Before starting........................6 4.1 Transport........................6 4.2 Installation........................6 4.3 Storage........................6 5 Installation / Start-up ......................7 5.1 Installing the brush spindles..................7 6 Operation...........................7 6.1 General operating instructions..................7 7 Troubleshooting.........................8... -
Page 4: Features
For metals and plastics: If you‘re looking for a compact, powerful and especially robust polishing motor, you can‘t escape the Wassermann WSM-2. It combines years of experience and technical progress in a polishing motor designed for long life and daily use. -
Page 5: Safety Guidelines
Wassermann Dental-Maschinen GmbH are not extended by these instructions. Application The WSM-2 polishing motor is a well-proven, efficient and maintenance-free single-phase AC motor (induction motor) with 2 speed options: 1500 rpm and 3000 rpm. It is fitted with low-noise, completely maintenance-free ball bearings. Shaft ends have 9 mm standard tapers for mounting the brush spindles. -
Page 6: Before Starting
Before starting Transport Before transporting the unit, ensure that it has been unplugged from the power socket. Make sure that it is packed correctly in order to avoid accidental damage. Be sure to check for any transport damage when unpacking the goods. Note down any damage if found. -
Page 7: Installation / Start-Up
Installation / Start-up Before starting the unit, connect up the following: Installing the brush spindles To use the polishing motor, you have to install the brush spindles, and that involves first removing the nuts. Use a cloth to clean the shaft ends and then replace the nuts. Use compressed air to remove dust and grime from the brush spindles, then install the spindles as marked: L = left and R = right. -
Page 8: Troubleshooting
Troubleshooting Fault Cause Remedy Ball bearing noise Faulty bearings Change bearings Spindles slip Spindles too loose Tap spindles lightly with a hammer Spindles can not be Spindles too tight Contact Service undone on taper If the above recommendations do not solve the problem, contact your dental depot or our service department. -
Page 9: Maintenance
Maintenance The unit does not require any servicing. Just make sure that the device is kept clean. Repairs Servicing or repairs to the unit has only to be carried out by qualified technicians. Only original spare parts are to be used. Responsibility for the product is voided if unauthorised persons alter it or if inappropriate components are installed. -
Page 10: Warranty
This warranty does not cover damage caused by improper use, external mechanical causes, transport damage or interference with the unit by unauthorized persons. Technical data WSM-2 Item no.:155999 Voltage* 220–240 V / 50/60 Hz Power consumption 2.3 A... -
Page 11: Ec Conformity Certificate
W A S S E R M A N N Product description: Polishing motor Dental-Maschinen GmbH for dental Rudorffweg 15 - 17 applications D-21031 Hamburg Model: WSM-2 Item no. 155999 Applicable DIN EN 61010-1 standards: DIN EN 61000-6-3 DIN EN 61000-6-1 DIN 45635-1 DIN EN 60335-1 Hiermit wird bestätigt, dass die oben bezeichnete Maschine den genannten EG-Richtlinien...