Hampton Research HR8-165 User Manual

22mm x 1.0mm
Square Cover Slide Gizmo
User Guide
Compatibility
The 22 mm x 1.0 mm Square Cover Slide Gizmo is compatible with:
• 22 mm diameter, plain Square glass cover slides (1.0 mm thick)
• 22 mm diameter, siliconized Square glass cover slides (1.0 mm thick)
Recommended Square Glass Cover Slides
HR3-219 - 22 mm x 1.0 mm Plain Square cover slides - 4 oz pack
(~ 75 slides)
HR3-221 - 22 mm x 1.0 mm Plain Square cover slides - 40 oz case
(~ 750 slides)
HR3-223 - 22 mm x 1.0 mm Siliconized Square cover slides - 4 oz pack
(~ 75 slides)
HR3-225 - 22 mm x 1.0 mm Siliconized Square cover slides - 40 oz case
(~ 750 slides)
Description
The Dispenser holds up to 1 pack of 22 mm x 1.0 mm plain or siliconized
Square cover slides. The dispenser is fitted with a metal
movement when loading and unloading cover slides. The Dispenser moves
to the right and left ends of the cover slide Gizmo along two chromed
The rails are positioned over the cover slide
to the 22 mm x 1.0 mm Square Cover Slide Gizmo with 2 mm allen head
screws. A top edge of the Platform is notched at each cover slide position to
allow finger or forceps access to the cover slides dispensed onto the Platform.
The Base has four rubber feet to keep the 22 mm x 1.0 mm Square Cover
Slide Gizmo flat and stationary. A black metal
plied with the 22 mm x 1.0 mm Square Cover Slide Gizmo fits over the
Dispenser to keep cover slides clean during operation. See Figure 2.
Figure 1
Top View of the 22 mm x 1.0 mm
Square Cover Slide Gizmo
Dispenser
Metal Knob
Using the 22 mm x 1.0 mm Square Cover Slide Gizmo
1. Insert the metal Tab into the bottom slot of the
See Figure 2.
Knob to allow easy
Platform . Each Rail is secured
Cover Slide Chamber
Base
Chrome Rail
Cover Slide Chamber
Figure 2
Cover Slide Chamber
Tab
2. Position the chamber flat onto the table. Open the chamber door and
carefully insert the 22 mm x 1.0 mm plain or siliconized Square cover slides
toward the bottom side of the Cover Slide Chamber where the tab is inserted.
Figure 3.
Figure 3
Opened Chamber
Door
Rails
.
3. Carefully position the 22 mm x 1.0 mm Square Cover Slide Gizmo such
that the metal knob on the dispenser is facing you. Clean any dust or debris
from the 22 mm x 1.0 mm Square Cover Slide Gizmo. Position the Dis-
penser all the way to the left end of the 22 mm x 1.0 mm Square Cover Slide
Gizmo. (Figure 1). Be sure no cover slides are positioned on the Platform to
sup-
the right of the Dispenser.
4. Align and insert the slide chamber into the slide dispenser. Remove the
metal tab.
5. There are two ways one can dispense the slides on the gizmo.
2 mm Allen
Screw
the knob attached to the Dispenser and slide the Dispenser all the way to the
right. Or, Place your thumb and first finger gently onto the front and back
top edge of the Dispenser, no need to press down on the Dispenser. Slide the
Dispenser all the way to the right end of the Platform until the Dispenser
is against the right end stop. Six cover slides will be positioned onto the
platform. See Figure 4.
Figure 4
Notched
Platform
.
Solutions for Crystal Growth
HR8-165
Insert Tab here
Begin filling
slides here
Tab inserted into
Chamber
Gently grab