Table of Contents
Advertisement
Quick Links
PS
SE60
PS
SE100
Polyamp
mp AB
Box 925
5
191 29
SOLLENTU
UNA
Sweden
n
In
nstalla
ation M
AC
C/DC p
power
PSE6
60, PS
Option
n T3
www.p
olyamp.com
info@p
polyamp.se
Tel: +4
46 85946930
Tel: +4
46 85946930
Manua
al
r supp
lies
SE100
PSE
with option
chas
sis mountin
m
EU
U VAT no SE
DU
UNS no 35-4
00
CA
AGE S4231
05
NC
CAGE S423
Ma
anual PSE-A
AC.docx
n N wall DI
IN and
ng
H15-
-S connecto
Conn
nector holde
optio
on N
E55610327
76301
430-3372
1
or
er for
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Polyamp PSE Series
Summary of Contents for Polyamp PSE Series
- Page 1 Option n T3 SE60 chas sis mountin SE100 H15- -S connecto Conn nector holde er for optio on N Polyamp mp AB www.p olyamp.com U VAT no SE E55610327 76301 Box 925 info@p polyamp.se UNS no 35-4 430-3372 191 29...
- Page 2 INSTAL LATION M MANUAL PSE serie es AC inpu Warran All Pol lyamp DC C/DC conv verters are e warrante ed against defective material a workm manship. T This warran nty is vali id for 24 m months fro om the dat te of deliv ery.
-
Page 3: Table Of Contents
INSTALLATION MANUAL PSE series AC inputs CONTENT Before installation ......................4 Cable and pin dimensioning ..................4 Inrush current limit ....................4 Input Fuse ......................... 4 Installation .......................... 5 Parallel connection ......................6 ... -
Page 4: Before Installation
The power supply type name consists of 1.1 Cable and pin dimensioning model name PSE60 and PSE100 followed by The PSE series is using a DIN 41621 H15 input code and output voltage. Two examples: connector intended for 3HE Euro format mounting. -
Page 5: Installation
6 f for the outpu ut over see S Section 5 pag ge 9. 3. Plug in the unit. R Read from bu ullet 3 below volta ge protection n page 10. 2011-04 Polyamp A AB Copyright t 2000-2011 age 5(13) -
Page 6: Parallel Connection
INSTALLATION MANUAL PSE series AC inputs • The series diode protects the converter output If you intend to use alarm feature, from external voltage sources. please consult section 7 Under voltage Alarm on page 10. If the series diode is used, we recommend to 5. -
Page 7: Connecting Systems In N+1 Configuration
0.5% % of nominal outpu ut voltage. 2011-04 Polyamp A AB Copyright t 2000-2011 age 7(13) -
Page 8: Adjusting Output Voltage When Units Are Paralleled On The Output
INSTAL LATION M MANUAL PSE serie es AC inpu 3.6 Ad djusting o output volt tage when nits are pa aralleled o on the 5. Repeat fr rom 3. until y you reach the e desired utput output vo oltage at the l load. -
Page 9: Output Voltage Sense, Option S
Longer s sense leads th han 3 m is no recomme ended. The v voltage differ rence between the load and d the convert ter should no 2011-04 Polyamp A AB Copyright t 2000-2011 age 9(13) -
Page 10: Logic Signal Alarm
The relay y is rated 30 V 0.5A (a.c. & d.c.). For high her voltage/cu urrent relay r rating please contact P Polyamp. The alarm m relay can be connected d in two ways: 1. Norm mally Open ( (NO). -
Page 11: Isolation Voltage Test
7. Turn n off the iso olation tester r and Ω disch harge the te est voltage w with a 10 MΩ resis stor between n output and d case. 2011-04 Polyamp A AB Copyright t 2000-2011 ge 11(13) -
Page 12: Dc Isolation Test Input To Output And Input To Case
INSTAL LATION M MANUAL PSE serie es AC inpu arning! An isol lation test sha all only be pe erformed by person nel aware of the dangers a and hazards of the t test. Figure 13. In nput to outpu ut and input t to case isolation vol... -
Page 13: Trouble Shooting
Warranty The Power supply output may be in All Polyamp DC/DC converters are warranted current limit due to excessive output against defective material and workmanship. current or an external short-circuit on the This warranty is valid for 24 months from the output.
Need help?
Do you have a question about the PSE Series and is the answer not in the manual?
Questions and answers