Related Manuals for Velbus VMB4RYNO
Summary of Contents for Velbus VMB4RYNO
- Page 1 Programmable 4-channel relay module for Velbus system...
-
Page 2: Table Of Contents
Termination ........................... 12 Configuration ........................13 Address ..........................13 Relay Contact Behaviour ....................13 Control Functions ......................13 CHECKING THE SOFTWARE VERSION ................17 VMB4RYNO 4-channel relay module user manual - version 1... -
Page 3: Description
This relay module is suited for switching on or off the lighting in the living room, the garden fountain, the mains outlets in the children’s room, and many more. This is only suited for use in a Velbus system. Multiple functions, e.g. switching on/off timers, are to be programmed via the Velbuslink software. - Page 4 5 hours and 10 hours in steps of 30 min o 10 hours and 24 hours in steps of 1 hour o 2 days o 3 days o no switch-off timer VMB4RYNO 4-channel relay module user manual - version 1...
-
Page 5: Velbus Characteristics
VELBUS CHARACTERISTICS • 2-wire communication for Velbus data and 2 wires for power • data transfer: 16.6 kbit/s • serial data protocol: CAN (Controller Area Network) • short-circuit proof (towards (-) or (+) of power) • bus error indication: 2 short blinks of the operation mode LED •... -
Page 6: Overview
LED Relay contact channel 1 Velbus RX (receive) LED Relay contact channel 2 Velbus TX (transmit) LED Relay contact channel 3 Relay contact channel 4 output status Velbus Velbus power supply VMB4RYNO 4-channel relay module user manual - version 1... -
Page 7: Led Indications
• blinks slowly when timer 2 is On LED: running lights when power • blinks shortly twice at voltage is present communication error Rx LED: lights at Velbus data reception Tx LED: lights at Velbus data transfer VMB4RYNO 4-channel relay module user manual - version 1... -
Page 8: Local Control
LOCAL CONTROL Remove the cover. Local control: on or off VMB4RYNO 4-channel relay module user manual - version 1... -
Page 9: Use
The relay module features 4 non-voltage NO contacts wich allow you to switch mains-voltage (230V) and low- voltage (12 or 24V) consumers. The module is integrated into the Velbus system and controlled through the VMB4PD control panel or by means of pushbuttons connected to a VMB8PB pushbutton interface, VMB6IN or any other relay module. - Page 10 A double-pole load (e.g. mains outlet) requires an extra double-pole relay. A triple-pole load (e.g. water heater) requires a quadrupole relay. VMB4RYNO 4-channel relay module user manual - version 1...
-
Page 11: Low-Voltage Connection Diagram
The module is also suitable for controlling 12V or 24V LED bulbs or strips. The input will then be connected to a low-voltage power supply (12V or 24V). Choose a power supply which can deliver the required consumption while the total consumption does not exceed 12A. VMB4RYNO 4-channel relay module user manual - version 1... -
Page 12: Termination
Remove the cover. Termination ® Generally, only 2 ‘TERM’ terminators must be used in a complete Velbus installation. Usually, this will be on one module inside the distribution box and on the module which is physically located furthest from the distribution box. -
Page 13: Configuration
Control Functions The relay module is controlled through pushbuttons connected to the Velbus system via a pushbutton interface or control panel. You may assign up to 39 different pushbuttons. Each pushbutton may activate a different function. - Page 14 The output is thus repeatedly open and closed. The switch-on and switch-off delays can be set. Pressing the pushbutton while the interval timer is running will stop the interval timer. VMB4RYNO 4-channel relay module user manual - version 1...
- Page 15 Toggle inhibit at pushbutton Pressing the pushbutton will switch off the relay for a preset time. press The functions will still be active internally. Repressing that same pushbutton will cancel the inhibition mode. VMB4RYNO 4-channel relay module user manual - version 1...
- Page 16 5 hours and 10 hours in steps of 30 min o 10 hours and 24 hours in steps of 1 hour o 2 days o 3 days o no switch-off timer VMB4RYNO 4-channel relay module user manual - version 1...
-
Page 17: Checking The Software Version
If a newer version is available, download it. Connect the Velbus interface to a PC and run the upgrade-software and follow the instructions on the screen. Remark: Upgrading a module is not without risk. Do not interrupt the process! If for any reason the upgrade should fail, the module will cease normal operation. - Page 18 Refer to our website for more information: www.velbus.be VMB4RYNO 4-channel relay module user manual - version 1...