Do you have a question about the VT400 and is the answer not in the manual?
Questions and answers
bob zenner
February 28, 2025
there is a pounding noise inside machine by motors
1 comments:
Mr. Anderson
May 14, 2025
A pounding noise inside the Vibratrim VT400 machine could be caused by the power settings being too high relative to the user's body weight and posture. When the machine is set too powerfully, it can move more than the user can stabilize, leading to excessive internal motion and noise. Adjusting the power settings to match the user's weight and comfort level may reduce the pounding noise.
This answer is automatically generated
Shane
May 19, 2025
Do you know where I could get a switch for a VT- 400 vibra trim. Thanks
Table of Contents ●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●● Introduction VibraTrim Illustrations VibraTrim diagram and parts description Control Panel Display & Description Assembly Instructions and Procedures Operation Instructions Preset programs User Programming for USB Flash Drive Features ...
The VT400 is the fourth model that we have produced .All of our models feature the oscillation style of vibration. We believe this is the best form of vibration for the body as it is mimicking the natural walking movement.
Page 4
VibraTrim Diagram Parts Description 1. Screw (M5X8) (4 for each handle) 8. Screw (M8X55) (2 screws) 2. Display Board 9. Gasket (8 pieces) 3. Signal Line Connector (upper) 10.Signal Line Connector(Lower) 4. Decoration Cover 11. Vibration Plate 5. Handrail 12. Base Cover 6.
Control Panel Display Buttons and Displays 1. Heartbeat Indicator 9. Time and Vibration Mode Change Button 2. Heartbeat/Mode Display 10 Time ( -- ) Button 3. Spiral Speed Display 11 Time ( + ) Button 4. Function Indicator 12 Oscillation Vibration Speed/Time Adjust Button 5.
Page 6
Assembly Instructions This unit is very heavy and requires two adults to assemble. Place the carton on the floor with the top of the box up. Open the carton and fold back the lid flaps. Then gently roll the carton over on its top. Lift off the carton, the bottom piece of the Styrofoam packaging and remove the plastic bag.
The time cannot be adjusted after a program is started. 5. DO NOT USE MORE THAN 20 MINUTES DURING ONE SESSION. The VibraTrim will stimulate lymphatic drainage. It is advisable to drink 500ml of lukewarm water, before use, in order to eliminate the toxic waste.
Page 8
Display Panel Button Description 1. Time Indicator. 2. Heart rate light: The light will flicker when the machine detects your pulse. 3. Manual Mode Light: This light is lit when manual mode is working. 4. USB Program Light: This light is lit when USB Program mode is working. 5.
Preset Programs There are 3 preset manual programs. Each manual program works for 10 minutes. Programs: P1:Cardiovascular Exercise Both vibration modes are active; the speeds change independently every five seconds. Spiral Vibration: 30、34…54、58、54… 6、 2、 6…22、26 Oscillation Vibration: 30、26… 6、 2、 6…54、58、54…38、34 P2:Detoxification Program Two vibration modes work together and the speeds change independently every five seconds Spiral Vibration:...
Page 10
User’s Programs Users can define six different programs with the provided USB flash drive. Setting the flash drive programs. 1. Insert the Flash Drive in a USP port and open the program by double clicking JT06B-1-USB . User’s Defined Program Speed of Spiral Vibration/\Step Seconds of Spiral Vibration/Step Program Graph...
Features & Benefits Features 3 Different Preset Programs Choose from 3 preset programs, each stimulating different profiles with different speed & vibration levels: P1: Cardiovascular Exercise P2: Detoxify Program P3: Body Perfection Program 60 Variants of Speed Range ...
Page 12
Boosts levels of Testosterone and Revitalization natural HGH The information above is based on the research of Whole Body Vibration that can be provided by VibraTrim. It is not implied that everyone will receive these results from a VibraTrim.
Page 13
Exercise Video The Exercise Video is 1 ¼ hour long video showing how to experience your VibraTrim for the first time and how to start your exercise program. This DVD is mailed the same day that your machine was shipped. If you haven’t received it a few days after receiving your unit please call 253-238-0675 and we will ship you another one.
It is now very easy to move. Do not use the VibraTrim for 30 minutes before and after meal. Only one person should be on the VibraTrim at a time. Doing so, may cause injury to yourself or damage to the VibraTrim.
Safety Precautions Heed the following warnings and precautions. This will help prevent damage to your machine and to yourself. When using the machine, comply with the operation instructions. Make sure that the power cord is not pinched by any portion of the machine or other object. The power cord may get damaged leading to shorting, electrocution or fire.
Page 16
Safety Precautions (Continued) Before cleaning, remove any water particles using a dry cloth to prevent moisture from entering the machine. A micro fiber cloth is highly recommended. Water particles could weaken the insulation causing a fire and damage to the unit. ...
Contraindications While the following list of medical conditions is not complete, we strongly advise that you consult with your physician before using the VibraTrim if any of the following conditions apply to you. Pregnancy Pulmonary embolism Acute hernia, discopathy, spondylolysis...
Humidity Range 40-80%. If the VibraTrim is not used for long period of time, cover it with a clean cloth to protect it from dust. Do not coil the wire cord as it may cause malfunction to the machine.
Delivering the complete piece of equipment for repair is often unnecessary, because the flaw can usually be fixed by replacing just the faulty part. It is preferable that you make any inquiries, about the warranty, directly to your VibraTrim retailer or to VibraTrim.
Need help?
Do you have a question about the VT400 and is the answer not in the manual?
Questions and answers
there is a pounding noise inside machine by motors
A pounding noise inside the Vibratrim VT400 machine could be caused by the power settings being too high relative to the user's body weight and posture. When the machine is set too powerfully, it can move more than the user can stabilize, leading to excessive internal motion and noise. Adjusting the power settings to match the user's weight and comfort level may reduce the pounding noise.
This answer is automatically generated
Do you know where I could get a switch for a VT- 400 vibra trim. Thanks