Related Manuals for Jet MPR-10HV
Summary of Contents for Jet MPR-10HV
- Page 1 Operating Instructions and Parts Manual Manual Pinch Roll Bender Model MPR-10HV 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-754430 Ph.: 800-274-6848 Edition 2 08/2018 www.jettools.com Copyright © 2016 JET...
-
Page 2: Important Safety Instructions
20. Keep tools sharp and clean for safe and best Do not use this machine for other than its performance. intended use. If used for other purposes, JET disclaims any real or implied warranty and holds 21. Deburr any sharp metal edges of the workpiece itself harmless from any injury that may result before placing it into the machine. -
Page 3: About This Manual
If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 4: Table Of Contents
L= length; W=width; H=height The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 5: Machine Dimensions
4.1 Machine dimensions Figure 4-1: machine dimensions... -
Page 6: Setup And Assembly
Position machine so there is enough room on Read and understand the entire all sides for general maintenance and feeding contents of this manual before attempting set- of materials. Anchor machine to a stable floor, up or operation! Failure to comply may cause preferably concrete, using lag screws or other serious injury. -
Page 7: Operation
7.0 Operation Deburr material to provide a smooth surface, and wipe off any oil on the material. Do not apply excessive pressure to material; use multiple passes to achieve desired bend. For very long materials, use a stock roller stand or similar device to keep workpiece parallel to ground and thus facilitate bending. -
Page 8: Standard Roll Dimensions
9.0 Standard roll dimensions Figure 9-1 10.0 Standard roll profiles and capacities Profile type Tolerance range (in.) Minimum (in.) 0.78 x 0.19 1.181 x 0.39 19.685 Flat (hard) 0.78 x 0.19 6.25 1.96 x 0.39 15.748 Flat (easy) 0.39 6.28 0.78 19.685 Square Tube, solid... -
Page 9: Roll Configurations
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET. Some parts are shown for reference only, and may not be available individually. -
Page 10: Mpr-10Hv Manual Pinch Roll Bender - Exploded View 1
12.1.1 MPR-10HV Manual Pinch Roll Bender – Exploded View 1... -
Page 11: Mpr-10Hv Manual Pinch Roll Bender - Exploded View 2
12.1.2 MPR-10HV Manual Pinch Roll Bender – Exploded View 2... -
Page 12: Mpr-10Hv Manual Pinch Roll Bender - Exploded View 3
12.1.3 MPR-10HV Manual Pinch Roll Bender – Exploded View 3... -
Page 13: Mpr-10Hv Manual Pinch Roll Bender - Parts List
12.1.4 MPR-10HV Manual Pinch Roll Bender – Parts List Index No. Part No. Description Size 1 ....MPR10HV-01 .... Stand Assembly ..................... 1 2 ....MPR10HV-02 .... Door ....................... 1 3 ....TS-2360121 ....Flat Washer ............. 12 mm ......2 4 .... - Page 14 ....MRP10HV-62-4 ..Spacer (not shown)..........Ø58 x ø12 mm ....6 ....MRP10HV-62-3 ..Spacer (not shown)..........Ø58 x ø20 mm ....4 ....JET-165 ..... JET Logo (not shown) ..........165x68mm ....1 ....LM000244 ....ID/Warning Label, MPR-10HV (not shown) ........... 1...
-
Page 15: Warranty And Service
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason ®... - Page 16 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com...