Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hear Technologies Hear back Pro
Summary of Contents for Hear Technologies Hear back Pro
- Page 1 PERSONAL MONITOR MIXER SYSTEM Firmware Version 1.0-5.X...
- Page 2 19. WARNING: To prevent injury, this apparatus must be securely attached to a rack in accordance with the installation instructions. 20. Detailed installation instruction in user manual. Hear Back PRO User Guide...
- Page 3 Hear Back PRO User Guide...
- Page 4 Directive. Safety: IEC 60065 -01+Amd 1 Nason Tackett EMC: EN 55022:2010 Senior Design Engineer 55024:2010 Hear Technologies FCC Part 15 991 Discovery Drive Huntsville, AL 35806, USA Date: August 15, 2014 Hear Back PRO User Guide...
- Page 5 Running unshielded CAT6* cables alongside AC cables, fluorescent light fixtures, or computer network wiring will also limit the maximum distance. It is always preferred to run the Hear Back PRO CAT6* cabling by itself, away from other cabling. ALL cabling should be electrically tested before use.
-
Page 6: Table Of Contents
Hear Back PRO User Guide... - Page 7 The Hear Back PRO System: Hub & Mixers Hub Mainframe • USB port on Hub makes updating firmware The Hear Back PRO system consists of two main for future features and upgrades a simple components: the Hub and the Mixer. The modular Hub...
-
Page 8: Hub Detail Diagram
FW V1 and V2 are not compatible with FW V5. To upgrade or downgrade, visit www.hearback.com/fwv5 Figure 2 *Cable complying with the National authorities (cable with an outer jacket or sleeving rated VW-1 or better). Hear Back PRO User Guide... -
Page 9: Hub I/O Cards
Waves protocol. SoundGrid. Our partnership with • Simultaneously sends and Waves makes it easy to directly connect the Hear Back PRO receives system to other high-end audio equipment (including directly 16 channels of digital audio out of a PC or Mac using only its Ethernet port). -
Page 10: Hbus
(could be internal or external). A logo chaining for very large systems. Use Hear Technologies CAT6* indicates no valid clock is present. If the logo is blinking RED, cables available in 50 foot length. -
Page 11: Hear Back Pro Mixer
• Side-mounted card slot for future expansion • Intercom feature allows communication to anyone with a Hear Back PRO Mixer or Virtual Mixer Card • Large master knob controls overall main mix, AUX, and intercom levels independently •... -
Page 12: Mixer Construction
PRESET OPERATION for the system to automatically return to volume control. The Hear Back PRO Mixer has the ability to store up to four system states in internal memory for easy session settings With FW V5, pressing PAN while in volume mode will show PAN recall. -
Page 13: Intercom
INTERCOM OPERATION The intercom function transmits the AUX IN source to everyone with a Hear Back PRO Mixer on the same network. By default, • A level meter is displayed using LEDs around the MASTER the input gain for the intercom source is set to 75%. When knob to show the current RMS level of the mix bus. -
Page 14: Headphone Amplifier
Mixer (firmware V1.3 or higher). The 22kHz signal is not only above the human hearing range, it is also at a very low level – just enough for the Hear Back PRO Mixer to detect. -
Page 15: Connecting And Calibration
Connect Hear Back PRO Mixers to Avoid adjusting the master volume too high and running the network card outputs using CAT6* cables and set all the inputs too low. -
Page 16: Hook-Up Diagrams
Analog Card Analog Card Network Card Channels 1-8 Channels 9-16 Channels 17-24 DANTE DIGITAL OUT HUB 2 Dante Card Virtual Mixer Network Card Up to 4 Additional Mixers Up to 8 Additional Mixers Dante Network Hear Back PRO User Guide... -
Page 17: Initial Setup
If you are using from 1 to 32 channels you will only need one settings are lost. If you choose to keep your settings, don’t exit Hear Back PRO Hub. If you are using 33 channels or greater you 128-Channel Mode. Submixing is not possible in 128-channel will need multiple Hubs. -
Page 18: Additional Button Combinations
EDIT CONFIG.TXT FILE assigned. A channel with all LEDs ON indicates it is the only Each Hear Back PRO Hub has its own editable CONFIG.TXT channel (or stereo pair) assigned to the submix. If only one file. To access, follow the steps below: channel (or stereo pair) is assigned, then adjusting volume, 1. -
Page 19: Technical Specifications
Note: 0 dBu = 0.775 Vrms. Specifications and features subject to change without notice. Hear Back PRO User Guide **Cable complying with the National authorities (cable with an outer jacket or sleeving rated VW-1 or better). ***Hub is capable of powering up to 32 Mixers with an additional power supply. -
Page 20: Troubleshooting And Operating Tips
○ Attempt to bypass the network switch, making a home run from Hub to Mixer, to verify this is the problem – if so, try a known good network switch from the list at the beginning of the Hear Back PRO User Guide. - Page 21 − Attempt to bypass the network switch, making a home run from Hub to Mixer, to verify this is the problem – if so, try a known good network switch from the list at the beginning of the Hear Back PRO User Guide.
-
Page 22: System Accessories
PRO MIXER DISTRO PRO INTERCOM FOOTSWITCH • Allows a single CAT6 cable to be run from a Hear Back PRO • Allows one microphone to double as both a vocal mic for the Hub to the stage/studio where the PRO Mixers are located. -
Page 23: Other Hear Technologies Products
The following are registered trademarks of Hear Technologies: Hear Technologies, Hear Back, Control Your Mix, Talk Back, Extreme Extender, Hearbuds, HearBus, and the “Jack” logo. All names and marks of other companies belong to those respective companies. - Page 24 ©2019 Hear Technologies 1-2019...
Need help?
Do you have a question about the Hear back Pro and is the answer not in the manual?
Questions and answers