Download
Share
Print this page
Colortrac SC Main Board Instruction Manual
  1. Manuals
  2. Brands
  3. Colortrac Manuals
  4. Scanner Accessories
  5. SC Main Board
  6. Instruction manual
Colortrac SC Main Board Instruction Manual

Colortrac SC Main Board Instruction Manual

Scanner main board
Hide thumbs

Advertisement

Quick Links

SCSM
Issue 2
C
o
l
o
r
C
o
l
o
r
Colortrac Ltd
SC Main Board Instruction Manual
This is a confidential controlled document and is the property of Colortrac Ltd.
It is not to be copied or reproduced in part or whole. It is intended for staff to read.
t
r
a
c
S
t
r
a
c
S
M
a
i
n
M
a
i
n
C
S
c
a
C
S
c
a
B
o
a
r
d
B
o
a
r
d
Page 1 of 21
Date: 12/02/14
n
n
e
r
s
n
n
e
r
s

Advertisement

loading
Need help?

Need help?

Do you have a question about the SC Main Board and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Colortrac SC Main Board

Summary of Contents for Colortrac SC Main Board

  • Page 1 SC Main Board Instruction Manual Issue 2 Date: 12/02/14 This is a confidential controlled document and is the property of Colortrac Ltd. It is not to be copied or reproduced in part or whole. It is intended for staff to read.
  • Page 2 Technical Support, Colortrac Ltd.  Colortrac Ltd shall not be liable for any damages, errors, issues or events that result from the use of the equipment or this manual. Page 2 of 21...

  • Page 3: Table Of Contents

    SC Scanners Main Board  CONTENTS Tools Required ......................... 4 Photos Information ........................5 Top Lid Cover ........................... 5 Main Board ..........................7 Calibration ..........................15 Firmware Installation ......................17 Auto-stitch ..........................19 Motor Speed ........................... 21 Page 3 of 21...

  • Page 4: Tools Required

    SC Scanners Main Board Tools Required To maintain the SC42 scanner the tools listed below are required. The tools are generally available; they are not the responsibility of Colortrac to supply. 1. Wristband 2. Pencil   Anti-static and cable.

  • Page 5: Photos Information

    SC Scanners Main Board Photos Information Some photos in this manual were taken during pre-production, and various stages of the SC scanner’s development. Some colours / backgrounds / designs shown may vary from the actual scanner being worked on. Some background panels may be shown in the photo to be removed when they actually don’t need to be;...
  • Page 6 SC Scanners Main Board 4. Carefully remove the 2 x M4 screws holding the right end of the Top Lid Cover. Take care not to drop the screws while removing them. 5. Close the Lid Assembly, making sure both Lid Latches lock securely.

  • Page 7: Main Board

    SC Scanners Main Board Main Board 4.1.1 Important Information. Before removing the Main Board, following the instructions to retrieve the Motor Speed value by using the Distributor’s Utilities area on page 21. 1. Remove the Aluminium EMC Tape covering the cables to the Main Board.
  • Page 8 SC Scanners Main Board 4. Remove the Main Board Cover and store in a safe place. 5. The Main Board cover for the SC25 is different than for the SC36 & 24, but should be removed in the same way as shown here.
  • Page 9 SC Scanners Main Board 8. Disconnect the Microswitch cable. 9. Disconnect the Mains Cable, Motor Control Cable and the 4 x LED Control Cables. 10. Disconnect the Control Board Cable. Page 9 of 21...
  • Page 10 SC Scanners Main Board 11. Remove the 6 x M3 screws holding the Main Board to the Lid Assembly. 12. Remove the Main Board using anti-static precautions. 13. To refit the Main Board, position onto the 6 spacers, making sure no cables are trapped under the board.
  • Page 11 SC Scanners Main Board 15. Reconnect the Microswitch cable. 16. Reconnect the Control Board Cable at J9, as well as the Motor Control Cable. 17. Re-insert the CIS Ribbon cables into J1 - J3, making sure the locking plate is up before inserting them.
  • Page 12 SC Scanners Main Board 18. When the CIS Ribbon cable is fully in place, secure it by pressing down both sides of the locking plate. 19. Reconnect the 4 x LED cables, ensuring the correct cable is inserted in the correct plug.
  • Page 13 SC Scanners Main Board 21. Reconnect the Power Connector. Then lower the Main Board Cover into place. 22. After making sure all the cables are in their appropriate cutout, and the USB connector is also in it’s cutout in the cover, fit 4 x M3 screws to hold the Main Board Cover in place.
  • Page 14 SC Scanners Main Board 24. Replace the Top Lid Cover as described in chapter “3 Top Lid Cover” page 5. 25. After fitting a Main Board into a SC25 or 36, run the SC Setparameters program at www.colortracsupport.com/S Cconfiguration.zip and set the Board to the correct scanner model.

  • Page 15: Calibration

    SC Scanners Main Board Calibration 1. Open the Lid Assembly and clean the Sensor Glass. Close the Lid Assembley. 2. Insert the Calibration Target so that the black part section is inserted first, face NOTE: It is necessary to remove the Magnetic Paper Guide so the target can fit centrally in scanner.
  • Page 16 SC Scanners Main Board 5. Click ‘OK’ to except the message. 6. After approx. 4 minutes, the ‘Calibration’ (or Normalisation) is complete. During calibration , the target will move through the scanner in stages several times. Page 16 of 21...

  • Page 17: Firmware Installation

    SC Scanners Main Board Firmware Installation 1. Download the latest firmware from the download site: 2. Click the browser button to locate the downloaded firmware. After selecting the firmware #########.cab file, click download. 3. Agree to the warning message. NOTE: It is important to allow the firmware to complete.
  • Page 18 SC Scanners Main Board 4. Once the download has finished it will request the scanner and software are both Re-cycled. Page 18 of 21...

  • Page 19: Auto-Stitch

    SC Scanners Main Board Auto-stitch 1. Insert the Calibration Target so that the black section is in first, and face up. NOTE: It is necessary to remove the Magnetic Paper Guide so the target can fit centrally in the scanner. 2.
  • Page 20 SC Scanners Main Board 4. On completion, click the ‘OK button. Useful Information:  FB stitch range: 0 – 32  LR stitch range: 0 – 88 Page 20 of 21...

  • Page 21: Motor Speed

    SC Scanners Main Board Motor Speed 1. On the Main Page, right click and enter the Distributors Utilities. Enter the password ‘p107’. 2. When changing a Main Board, this values might need to be recorded prior to removing the board if the reference lable is damaged or missing from under the scanner.