Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Super Sealer REI-90F
Summary of Contents for Super Sealer REI-90F
- Page 2 REI-90 tray sealer. Any troubleshooting or repairs other than cleaning must be referred to Super Sealer service center. Please contact Super Sealer Australia on 03 9013 2688 if you have any questions. Updated: 10 October, 2009 Page 2...
-
Page 3: Table Of Contents
Introduction......................4 Main Parts ......................4 ......................5 Specifications Operation .......................5 Control Panel......................6 Resetting Computer Program ................7 Roll Film Set-Up....................10 Date Printer/Coder ....................10 Mould Removal and Replacement..............11 ......................11 Upper Mould ......................12 Lower Mould Maintenance and Cleaning.................12 ....................13 Daily Maintenance ..................13 Air Pressure Controller Trouble Shooting Guide..................13 Wiring Diagram....................16 Updated: 10 October, 2009... -
Page 4: Introduction
Introduction Super Sealer REI-90F tabletop gas flushing sealing machine models are suitable for films from reel. Ideally suited for small to medium batch operations, new product development, testing and market samples. The machine offers superior quality machine suitable for small and medium food processing factories. -
Page 5: Specifications
2.1 Specifications REI-90F Machine Construction Stainless Steel/ Aluminium Alloy Output Capability Up to 8 cycles per minute Air Requirement 2HP (600KPa, 20L/M, 80 psig) Machine Dimension ~ 430Lmmx660Wmmx710Hmm Machine Weight ~ 80 kg Power Requirement 1Phase, 220-240Vac @ 10Amps Roll Diameter... -
Page 6: Control Panel
Control Panel Image 2. Sample Control Panel The control panel is where some of the functions of the machine could be adjusted and/or modified based on your specific machine requirements. Please note that the machine is delivered with predefined feature parameters and you may not need to change any of the defined settings. POWER ON/ OFF The power on/off switch to start/stop the operation of the machine. -
Page 7: Resetting Computer Program
ON OR OFF SELECTIONS The machine will not be performed the function when the setting is set to OFF. FILL GAS FLUSH ”RESET” Changes the computer operating function. Right display: displays the temperature in the normal operation, when an error occurs it shows the error code, and displays parameter values when the machine is under set mode. - Page 8 B1. Press ¦ S ET § until the left display shows P1-1, the right display shows “Temperature in degree celcius ” of the 1 set upper mould, press “▲” or “▼ ” to set up the new temperature. B2. Press ¦...
- Page 9 display shows and the right display will give a value between”001~255”, set the correct value for the length of film to be sealed and cut, press the “set” key to get and choose printer type. (5) Non-printed film with printer printing once each cycle. Press the ¦...
-
Page 10: Roll Film Set-Up
Roll Film Set-Up Setting Up the film roll is a simple step of following the direction as per the images below – with printer or without the printer. Wit Date Printer Without the Date Printer Date Printer/Coder Specification Type Manual Hot Ink Stamp Maximum Number of Lines Font / Font Size Times Roman 12 font... -
Page 11: Mould Removal And Replacement
Printer Ribbon Setting Mould Removal and Replacement ELECTRICAL HAZARD Always REMOVE the machine from the power outlet before performing any maintenance or cleaning works. BURN HAZARD • Cleaning and maintenance should be performed by your trained personnel only • Allow unit to cool at least 90 minutes before normal cleaning •... -
Page 12: Lower Mould
Removing the black screw • Holding the bottom part of the upper mould, slowly pull/ slide out • Lower Mould Lower Mould Function The main function of the lower mould is to hold the containers on their position for the sealing and the cutting function. -
Page 13: Daily Maintenance
S. E20: DC power circuit short (P.C board error). B. If any error occurs, an alarm will sound. To stop the alarm, please off the power for five seconds, then turn on the power again, if the alarm remains on, please contact your Super Sealer for service. ERROR... - Page 14 ¨ ¨ system error. 2 P.C.B error 2 Change P.C.B © © Temperature control Power on failed Reboot the power on key. If fail system error. again then. P.C.B error Heater not turned on after power is on. Change P.C.B ©...
- Page 15 © © Film eye-mark sensor in wrong Adjust the eye-mark sensor Sealing film stop at position position and clean the sensor. wrong position Film stop is in wrong position. Adjust the film roll and after sealing. clamp. © © Film material is not suitable for the Change the film material.
-
Page 16: Wiring Diagram
11. Wiring Diagram Updated: 10 October, 2009 Page 16 REF: REI-90-0611... - Page 17 Updated: 10 October, 2009 Page 17 REF: REI-90-0611...
Need help?
Do you have a question about the REI-90F and is the answer not in the manual?
Questions and answers