Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Teptron Move
Summary of Contents for Teptron Move
- Page 1 User manual MOVE- Bluetooth controlled motor for indoor blinds and shades...
-
Page 2: Table Of Contents
Venetian blinds installation 11.2 Calibration 11.3 Pairing and controlling with a smartphone app 11.4 Electrical connections 11.4.1 Rechargeable Batteries 11.4.2 Solar panel 11.4.3 Micro USB 11.5 Factory reset Technical specifications Disposal and recycling information Teptron AB, 2018-v2-en, main user manual MOVE... -
Page 3: Warnings And General Precautions For Safety
In these conditions always remove the batteries and use a suitable USB power adapter to power the product. Exact specification for the USB power adapter can be found in this manual. Read all safety instructions for any other products and/or accessories before using with the product. Teptron AB is not responsible for the operation of, or any damage caused by, third-party accessories or their compliance with safety and regulatory standards. -
Page 4: Regulatory And Safety Notices
RF exposure requirement. Le matériel est conforme aux limites de dose d'exposition aux rayonnements énoncés pour fac un autre environnement.ce dispositif a été évalué à satisfaire l'exigence générale de l'exposition aux rf. Teptron AB, 2018-v2-en, main user manual MOVE... -
Page 5: Product Description And Intended Use
This also makes it possible to link units together making them act as one. To ensure its function even under heavy load MOVE has a custom metal gearbox and the gears are made of metal. The electronics controlling the motor has a force limiting safety feature making it safe to use. - Page 6 MOVE go to the respective end positions. MOVE can always be stopped by clicking the “stop” button on the unit. This is true no matter if the initial run command originates from the push/click of buttons “run clockwise” or “run counter clockwise” or from the app.
- Page 7 Pic 3, Battery device overview 1. Release button 3. USB connector LED indicator The release button is used when detaching the battery from the MOVE device. The LED indicator can have the following states: Continuously slow blink: Charging Continuously rapid blink: Error indication The battery device can be charged with any USB power adapter.
-
Page 8: Bead Chain
Many different sizes of bead chain and connectors exist and MOVE is designed to fit as many as possible, but compatibility to make sure MOVE fits the product it’s about to be installed on need to be established before installation. -
Page 9: Cord Loop
The metal pieces that are bent around the cord loop center hole should grip the motor output axel. The cord need to be taut enough, so the cord doesn’t slip in the cord loop spool. Pic 5.1.1 Pic 5.1.2 Teptron AB, 2018-v2-en, main user manual MOVE... -
Page 10: Cords
6 Cords 6.1 Prepare the cord Products that are operated by just pulling a cord need some preparation in order for MOVE to operate them. 1. Remove all plastic parts from the cord 2. After removing the plastic parts make a knot on the end of the cord Pic 6.1.1... -
Page 11: Ways To Install
7 Ways to install 7.1 Mounting Plate Option 1 Use the Template to mark up the location for the unit. Option 2 Use the Mounting plate to mark up the location of the Unit. Teptron AB, 2018-v2-en, main user manual MOVE... - Page 12 Use screws and anchor to attach mounting plate to wall. Pic 7.1.3 The wall mounting plate Pic 7.1.4 Teptron AB, 2018-v2-en, main user manual MOVE...
-
Page 13: Install Unit
Locate the Mounting plate on previous locate position and use Philips screw driver or drill to install it. Pic 8.1.1 8.2 Attached Main unit to mounting plate Attach the Bead chain to main unit pulley as shown on pic and aline mounting Plate to main unit. Pic 8.2.1 Teptron AB, 2018-v2-en, main user manual MOVE... -
Page 14: Fixed Main Unit To Mounting Plate
8.3 fix Main unit to mounting plate Push main unit towards the mounting plate and secure main unit. Pic 8.3.1 Pic 8.3.2 Teptron AB, 2018-v2-en, main user manual MOVE... -
Page 15: Battery Pack
Alien battery pack unit to main unit and push it from underneath. Battery unit connection should line up with main unit connection Pic 9.1.1 9.2 Secure Battery pack with Main unit Pic 9.2.1 Teptron AB, 2018-v2-en, main user manual MOVE... -
Page 16: Installation Of The Motor And The Accessories
The motor inside MOVE has a torque of about 1Nm and incorrect installation and/or usage can be dangerous. Make sure that the cord or bead chain of the product you intend to install MOVE on is compatible, do not install if it does not fit. -
Page 17: Calibration
11.3 Pairing and controlling with a smart phone app MOVE can be controlled through a smart phone app after the app and MOVE have paired with each other. First the app should be placed in paring mode. The first step to do this is to click “add new unit” in the application. The second step is to choose the type of function the new unit should perform, after that the app will be in pairing mode. -
Page 18: Rechargeable Batteries
1. Insert the cable from the solar panel to the battery device USB connector (section 3, pic 3, position 3). 11.4.3 Micro USB Any 5-9VDC power adapter with micro USB type B connector can be used to power MOVE or be used to charge the battery pack. 1. Use the power adapter (section 3, pic 1, position 5) 2. -
Page 19: Disposal And Recycling Information
MOVE must be disposed of separately from household waste. When MOVE reaches its end of life, contact local authorities to learn about disposal and recycling options, or simply drop it off at your local Teptron retail store or return it to Teptron.
Need help?
Do you have a question about the Move and is the answer not in the manual?
Questions and answers