Table of Contents
Related Manuals for Elisra Electronic Systems Ltd. MWCBDA-SMR-1W60PS-9
Summary of Contents for Elisra Electronic Systems Ltd. MWCBDA-SMR-1W60PS-9
- Page 1 FCC ID: OIW CBDASMRPS9 INSTALLATION AND OPERATING INSTRUCTIONS The following is a copy of Installation and Operating Instructions of the MW- CBDA-SMR-1W60PS-9 Cellular Bi-Directional Amplifier/Booster. Exhibit 5 - Page 1 of 11...
- Page 2 FCC ID: OIW CBDASMRPS9 INSTALLATION OPERATING INSTRUCTIONS MW-CBDA-SMR-1W60PS-9 BI-DIRECTIONAL AMPLIFIER (COMPACT BDA) Exhibit 5 - Page 2 of 11...
-
Page 3: Table Of Contents
FCC ID: OIW CBDASMRPS9 TABLE OF CONTENTS PARAGRAPH PAGE NO BDA OVERVIEW BDA BLOCK DIAGRAM DESCRIPTION BDA BLOCK DIAGRAM DRAWING ELECTRICAL SPECIFICATIONS MECHANICAL SPECIFICATIONS ENVIRONMENTAL CONDITIONS BDA CONNECTIONS PERIODIC MAINTENANCE DIAGNOSTIC GUIDE MECHANICAL OUTLINE Exhibit 5 - Page 3 of 11... -
Page 4: Bda Overview
FCC ID: OIW CBDASMRPS9 BDA OVERVIEW: The BDA assembly provides an exceptional repeater/booster performances extend coverage area radio communications in buildings and RF shielded environments. Features such as high linearity power amplifiers are contributing for the overall improved system linearity performances. The unit is based on a duplexed path configuration, having sharp out of band attenuation for improved isolation between the receiving and transmitting paths. -
Page 5: Bda Block Diagram Drawing
FCC ID: OIW CBDASMRPS9 AGC RF AMPLIFIER DETECTER AGC CIRCUIT COUPLER Downlink AREA BASE ANTENNA STATION Duplexer Duplexer ANTENNA DETECTER (N-TYPE) AGC CIRCUIT (N-TYPE) COUPLER Uplink AGC RF AMPLIFIER BDA BLOCK DIAGRAM MW-CBDA-SMR-1W60PS-9 Exhibit 5 - Page 5 of 11... -
Page 6: Electrical Specifications
FCC ID: OIW CBDASMRPS9 ELECTRICAL SPECIFICATIONS: Frequency Range : Up Link : 896 – 902 MHz : Down Link : 935 – 941 MHz Passband Gain @ min attenuation : 60 dB minimum Passband Ripple : ±1.5 dB typical ° : 6.0 dB max Noise Figure @+25 C at max gain... -
Page 7: Mechanical Specifications
FCC ID: OIW CBDASMRPS9 MECHANICAL SPECIFICATIONS: Size : 9.84 x 9.61 x 4.53 inch (250 x 244 x 115 mm) RF Connectors : N-type Female Weight : 10 Lbs. (5kg.) approx. ENVIRONMENTAL CONDITIONS: The unit is designed for indoor applications: : - 30 °... -
Page 8: Bda Connections
FCC ID: OIW CBDASMRPS9 BDA CONNECTIONS The BDA AC power is supplied through a standard 3-wire male plug with phase, neutral and safety ground wires. The AC power is only used to supply a high efficiency DC switching power supply. The two amplifiers (Uplink and Downlink) and the Power On lamp use only DC power. -
Page 9: Diagnostic Guide
FCC ID: OIW CBDASMRPS9 DIAGNOSTICS GUIDE As mentioned before the BDA should provide long term, care free operation with no need of any periodic maintenance. This section will cover possible problems that may show up after installation. a. Gain Reduction Possible causes: Bad RF cables and RF connections to antennas, Damaged antennas. -
Page 10: Mechanical Outline
FCC ID: OIW CBDASMRPS9 MECHANICAL OUTLINE Exhibit 5 - Page 10 of 11... - Page 11 FCC ID: OIW CBDASMRPS9 Exhibit 5 - Page 11 of 11...
Need help?
Do you have a question about the MWCBDA-SMR-1W60PS-9 and is the answer not in the manual?
Questions and answers