Advertisement
Quick Links
Note: Please provide valve serial number (stamped on cover of valve) when ordering parts.
Thermometer
Hot Water
Inlet
G3600
Installation
1. Valve should be installed at a location where it can easily be
cleaned, adjusted or repaired.
2. The inlets are clearly marked on the valve body casting.
Connect the hot water into the inlet marked "HOT" and cold
water into the inlet marked "COLD. "
3. The checkstops furnished must be installed on both supply
lines as shown above.
4. Use solder or pipe cement sparingly. Supply pipes should
be flushed before the valve is connected. Flush outlet pipe
and valve as soon as it is connected.
Maximum Operating Pressure 125PSI (860 KPA) for Hot and Cold
Water. Maximum hot to cold water pressure differential is 5%.
Note: It may be necessary to recirculate the tempered water to the
face/eyewash should the piping be exposed to excessive hot or cold
conditions. Consult factory for proper piping.
Note: this is a control system which must be cleaned and maintained on a regular basis (see maintenance guide and record MGRG-1000).
Guardian Equipment
312 447 8100
1440 N North Branch
312 447 8101
Chicago, IL 60642
gesafety.com
Hot Water
Angle
Checkstops
1/2" Copper
Tube Inlets
Cold Water
Inlet
telephone
facsimile
Installation, Operation and Maintenance Guide
G3600 Series Thermostatic Mixing Valves
Tempered Water
Outlet
Inlet
IMPORTANT: THESE SYSTEMS ARE DESIGNED TO
PROVIDE MIXED WATER FROM 60 TO 90°F (15 TO
32°C) FOR EMERGENCY SHOWER APPLICATIONS
ONLY. CALL GUARDIAN EQUIPMENT FOR SYSTEMS
DESIGNED TO OPERATE AT TEMPERATURES
OUTSIDE OF THIS RANGE.
Cold Water
Inlet
G3650
rev. 0114 / © 2014 Guardian Equipment
Inline
Check
Redundant
Thermostatic
Mixing Valve
Primary
Thermostatic
Mixing Valve
1
Advertisement
Related Manuals for Guardian G3600 Series
Summary of Contents for Guardian G3600 Series
- Page 1 Consult factory for proper piping. Note: this is a control system which must be cleaned and maintained on a regular basis (see maintenance guide and record MGRG-1000). rev. 0114 / © 2014 Guardian Equipment Guardian Equipment 312 447 8100...
-
Page 2: Troubleshooting
SEE PAGE 5 FOR COMPLETE PARTS BREAKDOWN AND PARTS KITS. If installed on a circulated hot water system, make certain the valve is piped according to Guardian Equipment Required Methods of Piping (see page 3). Note: this is a control system which must be cleaned and maintained on a regular basis (see maintenance guide and record MGRG-1000). - Page 3 • Turn primary thermostatic valve to full hot and wait ten seconds. Note: this is a control system which must be cleaned and maintained on a regular basis (see maintenance guide and record MGRG-1000). rev. 0114 / © 2014 Guardian Equipment Guardian Equipment 312 447 8100...
- Page 4 EXCESSIVELY HOT WATER (OVER 90ºF) IS DANGEROUS AND MAY CAUSE SCALDING!! Note: this is a control system which must be cleaned and maintained on a regular basis (see maintenance guide and record MGRG-1000). rev. 0114 / © 2014 Guardian Equipment Guardian Equipment 312 447 8100...
- Page 5 Valves are furnished with lockable pointers. Note: this is a control system which must be cleaned and maintained on a regular basis (see maintenance guide and record MGRG-1000). rev. 0114 / © 2014 Guardian Equipment Guardian Equipment 312 447 8100...
-
Page 6: Limited Warranty
When properly installed and maintained in accordance with Guardian Equipment’s instructions, for a period of one year from date of shipment. During this period the Guardian Equipment will at its option repair or replace any product, or part thereof, which shall be returned, freight prepaid, to the Guardian Equipment factory and determined by Guardian Equipment to be defective in materials or workmanship.