Niigata seiki DTW-DL01 Instruction Manual

BluetoothBOX DTW-DL01
Thank you for purchasing BluetoothBOX, DTW-DL01.
Please read this document thoroughly for proper operation and in order to get the greatest benefit from the
product.
■OVERVIEW
Wireless adapter for Levelnic (DL-S3 Series, DL-m3 Series, DL-m3LS, DL-D3,DL-S3L).
※ ※ ※ ※ This adapter requires a standard USB Bluetooth Adapter (Bluetooth 4.0 or hig This adapter requires a standard USB Bluetooth Adapter (Bluetooth 4.0 or higher,) purchased separately.
This adapter requires a standard USB Bluetooth Adapter (Bluetooth 4.0 or hig This adapter requires a standard USB Bluetooth Adapter (Bluetooth 4.0 or hig
■FEATURES
● Can communicate with wide range of Bluetooth capable devices.
● Accepts a standard USB Bluetooth adapter, available worldwide.
■PART IDENTIFICATION
①Power ON/OFF Button (Red)
・When status LED is off, a short press will turn ON
power.
・When status LED is on, a short press will turn OFF
power.
・Hold down the Pairing Button and press Power Button
.
at same time to enter pairing (discovery) mode
USB-A Connector (Bluetooth icon)
②
Customer supplied USB Bluetooth adapter plugs in here.
Do not use to connect other USB devices.
※ For full communication distance capability, the PC's Bluetooth
interface must also be Class 1.
Data communication connector ("DATA")
③
Connects to the Levelnic with supplied Mini-plug
Communication Cable.
Pairing Button ("PAIRING")
④
Hold down the Pairing Button (using a thin tool) and press the Power Button at the same time to enter pairing
(discovery) mode .
Micro-USB connector ("CHARGE")
⑤
Connects to the included AC-USB charger and Charging Cable, or connect to PC to charge the device.
※ Do not use to connect other USB devices.
Charging LED (Power icon)
⑥
LED on when charging; goes off when complete.
Status LED
⑦
Power ON: LED=Red, communicating: LED=Green, Paring: LED=Blinking green, Pairing complete: LED=Blue,
Voltage low: LED=Blinking red
m3 Mounting
Instruction Manual
NIIGATA SEIKI CO., LTD
her,) purchased separately.
her,) purchased separately. her,) purchased separately.
Power ON/OFF Button
①
Data Communication Conn.
③
USB－A Connector
②
④ Pairing Button
⑦ StatusLED
Charging LED
⑥
⑤ Micro-USB Connector
Charging Cable Mini-Plug Communication
■MOUNTING
I
1. nstall a standard USB Bluetooth adapter by plugging it into the USB-A
connector of the adapter.
2. Mount the wireless adapter onto the Levelnic.
・ For Levelnic S3,
Loosen the battery case knob slightly and slide the Mounting Plate
(mounted on the Wireless Adapter) over the screw as shown at right
(Image 1).Image 2 shows the wireless adapter installed on the Levelnic.
· For Levelnic m3,
Loosen the battery case knob slightly and install the m3 Mounting
Bracket and re-tighten the knob.
Slide the Mounting Plate (mounted on the Wireless Adapter) over the
Bracket so it goes into the Slotted Hole in the Plate.
※ Slotted Hole can be seen at the top of the Plate in Image 1.
3. Plug the Min-plug Communication Cable into the Mini-plug connectors at each end.
■PAIRING
Turn on the communicating PC and enable the Bluetooth interface.
・
※For a PC which does not have a wireless interface, please provide a
standard Bluetooth 3.0 adapter and connect it to the PC.
※Do not install the Bluetooth drivers that come with the Bluetooth
adapter, it works with the standard Windows drivers.
※On the communicating PC, Open the Device Manager Window, and
under "Bluetooth Radios", confirm that "Generic Bluetooth Radio",
and "Microsoft Bluetooth Enumerator" are present.
※How to change to the Windows standard driver
1. Right-click on the "CSR Bluetooth Chip" (the device name may be different) in Device Manager.
2. Select "Update Driver Software"
3. Click "Browse my computer for driver software"
4. Select "Let me pick from a list of device drivers on my computer"
5. Check the "Show compatible hardware" check-box, and select "Generic Bluetooth Adapter", then click "Next"
・ On the Wireless Adapter, hold down the Pairing Button
and press the Power Button to enter pairing mode.
(Status LED will blink green)
・ Have the communicating PC or Tablet search for available
Bluetooth devices. (This procedure varies depending on
the computer. Please refer to the instruction manual for
the PC.)
・ Select "SKDL01" from the detected devices and begin pairing.
※ ※ ※ ※ The paring code dialogue window will be displayed; please select "Yes" regardless of number shown. (For Windows XP, The paring code dialogue window will be displayed; please select "Yes" regardless of number shown. (For Windows XP, The paring code dialogue window will be displayed; please select "Yes" regardless of number shown. (For Windows XP, The paring code dialogue window will be displayed; please select "Yes" regardless of number shown. (For Windows XP,
please enter please enter please enter "0000".) please enter "0000".) "0000".) "0000".)
(You will be unable to connect if you you select "The device is not displaying a code") (You will be unable to connect if you you select "The device is not displaying a code") (You will be unable to connect if you you select "The device is not displaying a code") (You will be unable to connect if you you select "The device is not displaying a code")
・When pairing is complete, the Status LED will be blue.
Image 1 Image 2