Table of Contents
Advertisement
Quick Links
MicroImage Video Systems warrants that each PXD510ET1 is free from
defects due to faulty materials or improper workmanship for a period of
one (1) year. MicroImage Video Systems further warrants that any part
which proves defective in materials or workmanship within one (1) year,
will be replaced or repaired at no cost to the user. Labor to replace
defective parts will be done without charge, provided the equipment is
returned to MicroImage Video Systems prepaid, insured and properly
packaged. Prior return authorization must be obtained from MicroImage
Video Systems.
NOTE
This warranty covers the MicroImage PXD510ET1 only.
CONDITIONS
This warranty is void if the warranted part has been altered or subjected
to abuse or misuse. Defective parts must be returned to MicroImage
Video Systems.
SOLE WARRANTY
This Warranty is in lieu of all other warranties expressed or implied
including, without limitation, any implied warranty or any implied
warranty of fitness for a particular purpose. MicroImage Video Systems
shall have the final right to determination as to the existence and cause of
any defect and its appropriate adjustment in accordance with the terms of
this warranty. In no event shall MicroImage Video Systems be liable for
any consequential or collateral damages.
All returns MUST have an RMA number. Please call, fax or email
for an RMA form. The RMA form will have the proper shipping
address for returns.
Phone
610-754-6800
Fax
610-754-9766
Email
techsupport@mivs.com
WARRANTY
RETURNS
Page 12
PIX/2 DSP
Operation Manual
Model PXD510E
Advanced DSP Video
Fade Controller
MicroImage Video Systems
division of World Video Sales Co., Inc
PO Box 331
Boyertown, PA 19512
Phone 610-754-6800
Fax 610-754-9766
sales@mivs.com
www.mivs.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MicroImage Video Systems PXD510E
Summary of Contents for MicroImage Video Systems PXD510E
- Page 1 In no event shall MicroImage Video Systems be liable for MicroImage Video Systems any consequential or collateral damages.
-
Page 2: Table Of Contents
SIGNAL STANDARD SELECTION ............. 4 Weight Contact MicroImage Video Systems for current data INPUT SIGNAL SELECTION..............5 The PXD510 series is manufactured in the USA by MicroImage Video Systems. CAMERA CENTER SPLIT MODE .............. 5 CONNECTIONS..................6 Power..................... 6 Inputs..................... 6 Outputs .................... -
Page 3: Description
Analog anti-aliasing filters Output Filters Digital plus 4 order analog anti-aliasing filters Board Level and OEM PIX/2 DSP products are also available. Horizontal Freq. Please contact your dealer or MicroImage Video Systems for RS-170/NTSC 15.734KHz typical CCIR/PAL 15.625KHz typical additional information. -
Page 4: Initial Setup
Save After setting the desired separator width and color, INITIAL SETUP pressing the FADE button will save the changes and return the unit to normal operation. The selected width Before the unit can be used, it must be set up for the proper video and color choices will affect both the vertical and the standard and input signal selections. -
Page 5: Input Signal Selection
INPUT SIGNAL SELECTION Exchange Pressing this key will exchange the A and B inputs when the unit is in split screen mode. This will cause the image from camera A to appear on the right or Setting the PIX/2 DSP to accept the proper input signal is bottom, rather than the top or left as normal. -
Page 6: Connections
Cam B Pressing the Cam B switch will change the display to CONNECTIONS show 100% of the camera B image. A Red indicator to the right of the switch will indicate this mode is selected. Power Plug the small connector on the end of the power module cord into H Split Pressing this key will cause the screen to be split, the power input connector on the PIX/2 DSP controller.
Need help?
Do you have a question about the PXD510E and is the answer not in the manual?
Questions and answers