Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Telect Manuals
  4. Control Unit
  5. ADF
  6. Installation manual

Telect ADF Installation Manual

Advanced distribution frame module
Hide thumbs Also See for ADF:

Advertisement

Quick Links

Download this manual See also: User Manual, Manual
Advanced Distribution Frame (ADF) Module Installation
and Fiber Routing Guide
Fiber :: Installation Guide
© Telect, Inc., All Rights Reserved, 12.5.16 rev.2
1.509.926.6000 :: telect.com
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the ADF and is the answer not in the manual?

Questions and answers

Related Manuals for Telect ADF

Summary of Contents for Telect ADF

  • Page 1 Advanced Distribution Frame (ADF) Module Installation and Fiber Routing Guide Fiber :: Installation Guide © Telect, Inc., All Rights Reserved, 12.5.16 rev.2 1.509.926.6000 :: telect.com...

  • Page 2: Technical Support

    22425 East Appleway Blvd., # 11 Liberty Lake, WA 99019 Telect assumes no liability from the application or use of these products. Neither does Telect convey any license under its patent rights nor the patent rights of others. This document and the products described herein are subject to change without notice.
  • Page 3 Equipped with posts, spools and unique arcs with wave-like ridges for grouping patch cords, the ADF efficiently manages 30 mm bend radius protection throughout the entire frame. Users can connect any two points within the frame with a 4.5-meter patch cord;...
  • Page 4 Advanced Distribution Frame (ADF) Module Installation and Fiber Routing Guide Fiber :: Installation Guide Cable Management Components ADF Main Frame ADF Inter-Bay ADF-26F-XI Storage Panel ADF-12INT-XI Posts Arcs Spools © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 5 3) Route fiber down around the bottom right spool © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 6 ✴ ✴ 3) Route fiber down and around the bottom right spool © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 7 ADF Frame in the position where the module is to be mounted. Step # 2) Locate the two mounting pegs on the rear of the module. © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 8 Main Frame Step # 4) Slide the module towards the rear of the frame, making sure the pegs are in the grooves, until it is seated properly © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 9 Step # 6) Secure the module within the frame by installing the two mounting screws on the front of the module using a large Phillips head screwdriver © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 10 Fiber Routing Guide Fiber :: Installation Guide NOTE: When proper installation is achieved, there should be no space between the module and the main frame as pictured here © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 11 © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 12 Fiber :: Installation Guide Step # 2) Remove the access plate at the rear of the module where the cable is to be installed by carefully pulling up on the black plunger © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 13 Remove the channel cover plate at the rear of the module by removing the two small screws using a small Phillips head screwdriver and then open the Velcro strap © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 14 900um routing area Step # 5) Open the slide at the back of the tray where the first sub-unit of the multi-fiber cable will be installed © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 15 Fiber Routing Guide Fiber :: Installation Guide Step # 6) Remove the top of the cable clamp by removing the single screw using a large Phillips head screwdriver © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 16 Fiber Routing Guide Fiber :: Installation Guide Step # 7) Place cable in the small half of the clamp and then reinstall the screw to hold the cable securely © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 17 900um management area NOTE: Heat shrink on Sub-units should not go beyond this line/point or bend radius violations may result in insertion loss © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 18 Fiber Routing Guide Fiber :: Installation Guide Step # 9) Continue to carefully route 900um fiber around the bottom spool, making sure all 900um fiber is inside the provided guide posts © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 19 Fiber :: Installation Guide Step # 10) Continue to carefully route 900um fiber up and around the top spool making sure that all fibers are inside the posts on the spool © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 20 Advanced Distribution Frame (ADF) Module Installation and Fiber Routing Guide Fiber :: Installation Guide Step # 11) Continue to route 900um fiber into remaining guide posts and towards the desired tray © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 21 Step # 13) Close the slider, holding the fibers out of the way to ensure that fibers are not pinched or broken © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 22 Advanced Distribution Frame (ADF) Module Installation and Fiber Routing Guide Fiber :: Installation Guide Step # 14) Remove the dust cap from the adapter, then carefully install the individual fiber in the desired location © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 23 Fiber Routing Guide Fiber :: Installation Guide Step # 15) Repeat Step # 14 until each individual fiber is in the correct location according to the desired configuration © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 24 Fiber :: Installation Guide Step # 16) Repeat steps 8-15 until all cable sub-units have been installed into the module according to the desired configuration and close all module trays © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 25 Fiber :: Installation Guide Step # 17) After the final cable sub- unit has been installed, restrap the Velcro around the sub-units at the rear entry port of the module © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 26 900um fiber is bundled together, restrap the Velcro around the fibers and inspect the management area one final time for any fibers that may need to be addressed © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 27 Fiber :: Installation Guide Step # 19) Replace the channel cover plate at the rear of the module with the two small screws, using a small Phillips head screwdriver © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...
  • Page 28 Step # 20) Replace the Access Plate by lining up the black plunger with the hole in the center of the 900um mangement area and pushing until it snaps into place © Telect, Inc., All Rights Reserved, 12.5.16 137828-2 1.509.926.6000 :: telect.com...