Related Manuals for ZMODO Greet Pro
Summary of Contents for ZMODO Greet Pro
- Page 1 Greet Pro Quick Start Guide...
- Page 2 Getting to know your Greet Pro The Greet Pro allows you to answer your door from any location. The Greet Pro is powered by your home's existing mechanical doorbell chime. This quick start guide will help you configure your Greet Pro for initial use. For detailed instructions and troubleshooting, please visit: www.zmodo.com/support...
- Page 3 Do not directly connect the doorbell to the Warning! primary power source (110/120VAC and 220/230/240VAC). The Greet Pro was designed to seamlessly replace a pre- existing doorbell button with a mechanical doorbell chime. If you do not have a mechanical doorbell, you must attach a 20 ohm/10 watt resistor (not included) between the connected doorbell and one wire from the power source.
- Page 4 Remove the mounting bracket from Slide down Greet Pro. Take your Greet Pro out of the packaging and slide down to remove the mounting bracket as shown below: Mark and drill the appropriate holes in the wall for the mounting bracket.
- Page 5 Fasten the mounting bracket onto the wall and connect the wires to the wire terminals. Tap the wall anchors with a hammer until the anchors are flush against the wall. Using the Philips tip for the provided screwdriver and the provided screws, fasten the bracket into place. Make sure that the two wires from Step 1 are fed through the opening and exposed.
- Page 6 Pro onto the mounting bracket by pushing firmly and sliding downwards. Note: If you are having difficulty sliding Greet Pro onto its mounting bracket, please loosen the security screws. Tighten the security screws until secure and restore the power to your doorbell from your circuit breaker.
-
Page 7: Connection Diagram
Installing your Power Accessory: Note: The power accessory is an optional add-on to regulate the power that flows to your Greet Pro. If you hear a buzzing sound from your chime, installing the power accessory will solve the issue. Before installing the power accessory, please make sure that the power to your doorbell is turned off from your circuit breaker. - Page 8 Remove the cover of your mechanical chime. First, locate your mechanical chime inside of your home. The mechanical chime is the device that rings when your doorbell is rung, and may commonly be a white box mounted on the wall. Loosen the screws of the chime terminals which have wires connected.
-
Page 9: Mobile Setup
Make sure you know the SSID (WiFi network name) and password of the 2.4GHz/5GHz WPA-PSK/WPA2-PSK WiFi network that you want your Greet Pro to connect to. Your network cannot be hidden. Make sure the network of the location where you install... - Page 10 This device can be set up with a Zmodo Beam. If you own a Beam, please follow the instructions in your Beam quick guide to Connectwith Beam connect your device instead. Note: Beam will only be able to connect your devices to a 2.4GHz network.
- Page 11 √ to proceed. Follow the on-screen instructions and select “Tap here to begin setup” to go to the WiFi settings page on your smartphone. Note: If you are using an iOS device, you will need to manually go to the WiFi settings page on your smartphone.
- Page 12 √ to proceed. If you see this screen, the app will connect your Greet Pro to your WiFi network. This may take a few minutes. Once it’s completed, please skip to step 11. If you do not see this screen, please proceed to step 8.
- Page 13 Tap to proceed. Note: The password provides an additional layer of security for your devices. You will not need to use this password when accessing your devices from the Zmodo app. It is not required, but it is highly recommended.
-
Page 14: Main Features
Greet Pro allows you to answer your door from anywhere with an Internet connection. See, hear, and speak to your visitors directly from your smartphone. You can access your Greet Pro's full features by using ® the Zmodo app on your Android... - Page 15 Pro from your device list to see what's happening on your front porch. Receive calls on your smartphone When someone rings Greet Pro, your home's chime will sound and you will receive a call on your smartphone. You can choose to...
- Page 16 View and save alert clips Greet Pro automatically records a short video clip whenever it detects motion, you receive a call, or you miss a call. Access these clips in the app and download them to your phone for safekeeping.
- Page 17 Enjoy more smart features in the future. Viewing Options All of your Zmodo devices will be bound to your Zmodo user account. You can access your camera and other devices by using the Zmodo app with any Android or ®...
- Page 18 You may need to improve your WiFi strength. Visit www.zmodo.com/support for suggestions. If you are installing your Greet Pro far away from your router, or if there are a lot of obstacles between your Greet Pro and your router, you may want to try connecting to a 2.4GHz network.
- Page 19 Support Having difficulty? You can use the Live Chat function in Zmodo app if you have any technical problems. Please follow the steps below: Access the “Me” page in the lower right corner of the Zmodo app and select “Zmodo Support”.