Advertisement
Table of Contents
- 1 5 Channel Handheld Remote
- 2 5 Channel Wall Remote
- 3 Operating Instructions
- 4 Pairing a New Motor to Your Handheld Remote or Wall Remote
- 5 Reverse Motor Rotation Direction
- 6 Setting New Upper and Lower Limits
- 7 Setting a “Favourite” Intermediate Stop Position
- 8 Removing a Motor from Your Handheld Remote or Wall Remote
- Download this manual
We thank you for your purchase of E-Motion™ automated shades from Elite Window Fashions™. Your shades have been
custom programmed by our factory to automatically stop at the top and bottom of your windows. Please consult this
guide for proper shade operation and programming.
5 Channel Handheld Remote
Channel LED Lights
1
2
Up
Stop /
Intermediate Position
Down
Channels Up / Down
Front View
5 Channel Wall Remote
Channel
LED Lights
Up
Stop /
Int. Position
Down
Channel Up / Down
User & Programming Guide
4
3
5
Transmitter
Model: BF-305W
Freq: 433.92MHz
Battery: CR2430
C
L
Rear View
(cover plate removed)
C
Limit
Button
Button
Operating Instructions
Raise Shade: Press and hold
Lower Shade: Press and hold
Stop Shade: Press
Intermediate Position: Press
stopped (must be set by user, see pg. 2 for setup).
Tilt Shade (High-Lite® & Sheer Horizontal Shades only):
Press and release
Limit
Change Channels: Press
channels. The numbered LED lights at the top of the
remote indicate the current channel. When all LED lights
are on, the remote will operate all shades.
Operating Instructions
Raise Shade: Press and hold
Lower Shade: Press and hold
Stop Shade: Press
Intermediate Position: Press
stopped (must be set by user, see pg. 2 for setup).
L
Tilt Shade (High-Lite® & Sheer Horizontal Shades only):
Tap
or
Change Channels: Press
channels. The numbered LED lights at the top of the
remote indicate the current channel. When all LED lights
are on, the remote will operate all shades.
Pg. 1
button for 1-2 seconds.
button for 1-2 seconds.
button while shade is in motion.
button when shade is
or
button.
or
arrows to change
button for 1-2 seconds.
button for 1-2 seconds.
button while shade is in motion.
button when shade is
buttons.
or
arrows to change
Advertisement
Table of Contents
Related Manuals for Elite Window Fashions e-motion
Summary of Contents for Elite Window Fashions e-motion
- Page 1 User & Programming Guide We thank you for your purchase of E-Motion™ automated shades from Elite Window Fashions™. Your shades have been custom programmed by our factory to automatically stop at the top and bottom of your windows. Please consult this guide for proper shade operation and programming.
- Page 2 2) Press and hold the “Limit” and “Up” buttons simultaneously until the motor jogs. follow us on: www.elitewf.com Copyright ©2017 Elite Window Fashions™ | 1 Applewood Crescent, Unit 1 Concord, Ontario, Canada L4K 4K1 Tel: 1-800-387-3566 | Fax: 1-800-665-3672 | email: customerservice@elitewf.com Pg. 2...
Need help?
Do you have a question about the e-motion and is the answer not in the manual?
Questions and answers
I broke my control when I dropped it and the battery doesn’t have contact, so it doesn’t work. I bought a new one and the directions said to hold the red button on the motor for 4-5 seconds to remove the motor from the old control. It is not cycling through two sets of jogs, so I know it is removed. It moves at the 1-2 seconds, but not at the 4-5 seconds
To troubleshoot the Elite Window Fashions e-motion control if it is not cycling through jogs after attempting to remove it from the motor:
1. Ensure you are pressing and holding the red button on the motor for 4-5 seconds, as required. The motor should cycle through two distinct sets of jogs.
2. Verify that the motor is powered and functional.
3. Make sure the motor is not grouped with other motors on the same channel. If it is, disconnect the power from other motors or temporarily remove them from the group channel.
4. Try the removal process again by pressing and holding the red button for the correct amount of time.
If the motor still does not jog, check for any power issues or faulty connections.
This answer is automatically generated