Using Your Splint Pan; Emptying Your Splint Pan; Care & Cleaning Of Your Splint Pan; Whitehall Splint Pans - Whitehall Forma-Splint SP-1501 Instructions For Operation And Care

temperature limit and counterclockwise to lower the
temperature limit. Please note that 1/8 of a turn is
approximately equal to ± 5ºF (-15ºC).
DO NOT turn the thermostat more than one full turn in
either direction. Reinstall the nameplate and fill the unit
with 3" (76mm) of water. During manufacturing the low
temperature is preset at 160ºF (71ºC) and the high
temperature at 175ºF (79ºC).
On the standard SP-1502 model, the temperature is
varied by turning the thermostat knob clockwise for an
increase and counterclockwise for a decrease in
temperature. The temperature on low setting should
approximate 140ºF (60ºC) and on high 190ºF (88ºC).
WARNING
!
Use the Splint Pan only as directed in this manual.
Any other use can cause injury.

USING YOUR SPLINT PAN

Once the digital display indicates the desired temperature,
the appliance will be ready for use. Allow +/- 3ºF (-16ºC)
temperature variance.
Always refer to the correct temperature & duration
specified by the splinting material manufacturer.
Be certain to heed all warnings as outlined in the
WARNING section (inside front cover of this manual).
Keep lid closed while water is heating up.
Carefully insert splinting material into tank and avoid
splashing HOT water. Avoid direct skin contact with HOT
water at all times. While splint material is immersed in
water, the lid should remain closed to help retain heat
inside tank. Remove splint material from tank only after it
has reached the manufacturer's specified duration. Use
caution when removing splint material from tank. Apply
splint material as specified by splint manufacturer's
instructions.
Keep the lid closed when appliance is not in use. Maintain
proper water level at all times. Immediately fill the
appliance with water to 3" (76mm) deep. Avoid allowing
water to reach a "very low water" level. A "very low water"
Whitehall Part #
1 6903-112-199
2 6903-212-199
3 6903-152-000
4 6903-160-000
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
Instructions for Operation and Care of Forma-Splint Thermal Bath

WHITEHALL SPLINT PANS

Description
Bottom Panel
Bottom Panel
Drain Ball Valve (Stainless Steel) 1/4-18 NPT x 1/4
Drain Barb (Stainless Steel) 1/4-18 NPT x 1/4
level would be any water level 3/4" (20 mm) or less water
depth as measured from the tank bottom. Never operate
appliance without water! These precautions will prevent
the appliance from over-heating and prevent potential
damage to the heating element.

EMPTYING YOUR SPLINT PAN

Before emptying (draining) your appliance, be sure that
the power switch is set to "OFF". Allow the appliance to
cool down before emptying. Lifting the lid will accelerate
this cooling. The Splint Pan must be unplugged when
emptying the reservior. The appliance has been provided
with a Drain Valve that has a 1/4" (6.35mm) barbed nipple
to attach a hose.
CARE & CLEANING OF
YOUR SPLINT PAN
Turn power switch "OFF" and unplug the unit from the
electrical receptacle. If necessary, drain the appliance by
following instructions as outlined in the "EMPTYING
YOUR SPLINT PAN" section.
When cleaning, rinsing, and/or drying your appliance
always rub in the direction of the stainless steel grain lines
to minimize marring or scratching the surfaces.
Use mild soaps, gentle non-abrasive detergents, or mild
mixtures of ammonia to routinely clean the surfaces of the
appliance. Be sure to always rinse with clean, warm water
and wipe dry. Use stainless steel cleaners such as 3M
Stainless Steel Cleaner/Polish, Sheila Shine
Stainless Steel Cleaner/Polish, Penny Brite, Cameo
Stainless Steel Cleaner/Polish, and EZ Brite, on stainless
steel surfaces. Strictly follow brand name manufacturer's
instructions on proper use of the stainless steel cleaner.
NOTE: The use of brand names is intended only to
indicate a type of cleaner.
DO NOT use bleach, chlorinated solvents, or other harsh
chemicals to clean your appliance. DO NOT use steel
wool to clean the stainless steel surfaces. For scaly, hard-
water spots use a strong solution of vinegar & water and
let it stand for approximately 5 minutes. Rinse with clean,
warm water and wipe dry.
SP-1501 SP-1501B SP-1502
x
x
x
, Twinkle
®
SP-
1502B
x
x x
x x x
x x x
®
5