Table of Contents
Advertisement
Quick Links
MT261
(Multi-Cutter Power Unit)
MC-S
(Straight Shaft Attachment)
MC-E
(Edger Attachment)
Owner's/ Operator's Manual
Completely read and understand this manual before using this product.
MC-PX/PS/PL
(Pruner Attachment)
MC-HT
(Hedge Trimmer Attachment)
MC-HTS
(Hedge Trimmer Attachment)
MC-T
(Cultivator Attachment)
Advertisement
Table of Contents
Summary of Contents for Bushranger MT261
- Page 1 MT261 MC-PX/PS/PL (Multi-Cutter Power Unit) (Pruner Attachment) MC-HT (Hedge Trimmer Attachment) MC-S (Straight Shaft Attachment) MC-HTS (Hedge Trimmer Attachment) MC-E (Edger Attachment) MC-T (Cultivator Attachment) Owner’s/ Operator’s Manual Completely read and understand this manual before using this product.
-
Page 2: Table Of Contents
It is essential that any operator of this Multi-cutter reads and understands the contents this manual before using the Multi-cutter. For additional assistance, contact any local authorized BUSHRANGER dealer. Important Notice The benefits to the consumer given by this warranty are in addition to other rights and remedies of the con- sumer under a law in relation to the goods or services to which this warranty relates. -
Page 3: Safety Instructions
5. Inspect the tool attachment and replace any parts that are cracked, chipped or damaged before using the Multi-cutter. 6. Never use a tool attachment or replacement parts that are not approved by BUSHRANGER. 7. Maintain the Multi-cutter according to the recommended maintenance intervals and procedures in the Maintenance section beginning on page 27. -
Page 4: Fuel Safety
9. Keep a firm footing and balance. Do not overreach. 10. Use the right tool for the job. Do not use the Multi-cutter for any job that is not recommended by BUSHRANGER. ＿ 3 ＿... -
Page 5: Safety And Instruction Decals
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any that are damaged or lost. MT261 (Multi-Cutter Power Unit) ON ENGINE ON ENGINE （Part No. 279811）... - Page 6 MC-HTS (Hedge Trimmer Attachment) ON GEARCASE （Part No. 407349） ON SHAFT （Part No. 217879） ON SHAFT （Part No. 221501） MC-PX/PS/PL (Pruner Attachment) ON SHAFT （Part No. 231896） MC-T (Cultivator Attachment) ON SHAFT （Part No. 221501） ON SHAFT （Part No. 221502） ＿...
-
Page 7: Product Description
Product Description 1. Shaft connector MT261 2. Loop Handle 3. Shaft Assembly (Multi-Cutter Power Unit) 4. Attachment Ring for Shoulder strap 5. Shaft Grip 6. Clutch Drum Housing 7. Engine 8. Air Filter 9. Fuel Tank 10. Throttle Cable and Stop Switch Wires 11. -
Page 8: Assembly
Assembly Loop Handle Installation Loop Handle Screw（4） 1. Place the loop handle and the bottom clamp on the shaft approximately 28cm (11 inches) from the end of the stop switch/ throttle trigger assembly. 2. Install the four screws and nuts. Tighten the screws evenly. 3. - Page 9 3. Insert the 3mm hex Wrench into the hole in the boss adapter and the guide slot in the gearcase to lock the attaching shaft. 4. Thread the trimmer head adapter into the attaching shaft, then tighten the trimmer head by hand. Note: The trimmer head adapter has left-hand thread.
-
Page 10: Mc-E (Edger Attachment)
MC-E (Edger Attachment) Guard Guard Stud Installing Guard Lock Washer Plate WARNING POTENTIAL HAZARD Flat Washer ・ Foreign objects can be thrown by Edger. Hex Nut WHAT CAN HAPPEN ・ Contact with thrown objects can cause personal injury. Flat Washer HOW TO AVOID THE HAZARD Knob Collar... -
Page 11: Mc-Px/Ps/Pl (Pruner Attachment)
MC-PX/PS/PL (Pruner Attachment) Guide bar and saw chain installation CAUTION ・ In order to prevent cuts, be sure to wear gloves when handling the guide bar and saw chain. ・ Maintain the tension of the saw chain properly at all times. ・... -
Page 12: Mc-T (Cultivator Attachment)
Installing Shaft Assembly and Gearcase Squared Attach the shaft assembly to the pruner gearcase assembly. Shaft Assembly Note: Carefully inspect both ends of the drive shaft protruding Locating Hole from the drive shaft tube. The squared end of the drive shaft positions toward the connector of the power unit. -
Page 13: Attaching Shoulder Strap
Attaching Shoulder Strap WARNING POTENTIAL HAZARD ・ Without the Shoulder Strap Installed on the multi-cutter, the blade can produce side thrust which can expose the operator and bystanders to blade contact. WHAT CAN HAPPEN ・ Contact with Brushcutter blade can cause severe personal injury. HOW TO AVOID THE HAZARD ・... -
Page 14: Before Operation
Before Operation Chain Oil (Pruner Attachment) Oil tank cap 1) Adding oil 1. Remove the oil tank cap and pour the chain oil (SAE #10W-30) into the oil tank. 2. Once the oil has been poured into the oil tank, tighten the oil tank cap to securely close the tank. -
Page 15: Engine Oil And Fuel
Engine Oil and Fuel 1. Mix and pour fuel outdoors and where there are no sparks or flames. 2. Always shut off the engine before refueling. Never remove the Multi-Cutter fuel tank cap while the en- gine is running or immediately after stopping the engine. WARNING POTENTIAL HAZARD ・... -
Page 16: Mixing Petrol And Oil
Recommended Oil Type Only use a two-stroke engine oil formulated for use in high-performance, air-cooled two-stroke engines. IMPORTANT: Do not use two-stroke oil intended for water cooled outboard motors. This type of two- stroke engine oil does not have the additives for air-cooled two-stroke engines and can cause engine damage. -
Page 17: Starting And Stopping
4. If the engine fails to start after three to four pulls, follow the instructions in the Cold Starting Procedure section above. If the engine fails to start after you follow the above procedures, contact an authorized BUSHRANGER dealer. To Stop the Engine 1. -
Page 18: Idle Speed Adjustment
Turn the screw out (counter-clockwise) to decrease the engine idle speed. If idle speed adjustment is necessary, and after adjustment the cutting attachment rotates or the engine stalls, stop using the Multi-cutter immediately! Contact your local authorized BUSHRANGER Dealer for assistance and servicing. ＿ 17 ＿... -
Page 19: Operation
Operation MC-S (Straight Shaft Attachment) WARNING POTENTIAL HAZARD ・ Foreign objects can be thrown by the Multi-Cutter. WHAT CAN HAPPEN ・ Contact with thrown objects can cause personal injury. HOW TO AVOID THE HAZARD ・ Never operate the Multi-Cutter without the blade guard in place. CAUTION ・... - Page 20 ・ If the trimmer head becomes jammed, stop the engine immediately. ・ Make certain all moving parts have stopped and disconnect the spark Pull plug before inspecting the equipment for damage. ・ Never use a unit that has a chipped, cracked or broken trimmer head. Red Band Shoulder Strap...
- Page 21 CORRECT INCORRECT Cutting Blades 1. Use only the correct blade (BUSHRANGER genuine part) approved for the application and model Brushcutter. 2. Carefully check the condition of the blades before and after operation. 3. Sharpen dull blades. Replace any blade that is worn, cracked or damaged.
-
Page 22: Mc-E (Edger Attachment)
MC-E (Edger Attachment) WARNING POTENTIAL HAZARD ・ Foreign objects can be thrown by Edger Attachment. WHAT CAN HAPPEN ・ Contact with thrown objects can cause personal injury. HOW TO AVOID THE HAZARD ・ Never operate the Edger Attachment without the blade guard in place. ・... -
Page 23: Mc-Ht/Mc-Hts
Setting Depth of Cut Guard IMPORTANT: Set the depth of cut before you start the engine. Increase the 1. Loosen the knob holding the guard to the plate. Decrease the Depth of Cut Depth of Cut 2. Rotate the guard as necessary to set the depth of cut. Note that: ・... - Page 24 Adjusting the angle of the blades [MC-HTS] CAUTION ・ Do not touch the sharpened edges of the cutting blades. The cutting blades are extremely sharp and dangerous. Always wear gloves to help protect your hands and fingers from injury. ・ Do not hold any part other than the handle when adjusting the angle of the blades.
-
Page 25: Mc-Px/Ps/Pl (Pruner Attachment)
MC-PX/PS/PL (Pruner Attachment) DANGER ・ Do not stand immediately below the branch that is to be cut. The branch may fall directly below and the branch may also bounce off other branches or the ground in an unexpected direction and cause injury to the worker. ・... - Page 26 Pruning thick branches Attempting to cut a thick branch in one go often results in the guide bar jamming in the branch or otherwise encountering difficulties in cutting. The method described below makes cutting thick branches easier: 1. First of all, cut a section slightly away and on the lower side of the desired area of the branch to be cut.
-
Page 27: Mc-T (Cultivator Attachment)
MC-T (Cultivator Attachment) CAUTION ・ Read the Safety instructions beginning on page 2 concerning proper use of the Multi-Cutter. Operating Position Before using the Multi-Cutter with Cultivator Attachment, check the following: 1. The unit may be on operator’s right side. The operator’s right hand should be holding the shaft grip, with his or her fingers on the throttle trigger. -
Page 28: Maintenance
Maintenance Air Filter Maintenance Interval Knob ・The air filter should be cleaned daily, or more often when working in extremely dusty conditions. ・Replace after every 100 hours of operation. Air Filter Cleaning 1. Remove the foam element. 2. Clean the foam element with warm, soapy water. Let the element dry completely. -
Page 29: Spark Plug
Cylinder Cooling Fins Maintenance Interval ・ The cylinder cooling fins should be cleaned after every 25 hours of operation, or once a week, whichev- er comes first. ・ Air must flow freely around and through the cylinder cooling fins to prevent engine overheating. Leaves, grass, dirt and debris build-up on the fins will increase the operating temperature of the engine, which can reduce engine performance and shorten engine life. -
Page 30: Mc-S (Straight Shaft Attachment)
MC-S (Straight Shaft Attachment) Gearcase Maintenance Interval Bearing Lube (P/N.211337) The gearcase should be checked for lubrication after each 30 Grease Plug hours of use. Plug Hole Gearcase Lubrication Remove the cutting attachment and the boss adapter. Clean any Gearcase dirt and debris from the area between the boss adapter and the gearcase. -
Page 31: Mc-Ht/Mc-Hts
MC-HT/ MC-HTS (Hedge Trimmer Attachment) Adjusting Cutting Blades CAUTION ・ Do not touch the sharpened edges of the cutting blades. The cutting blades are extremely sharp and dangerous at all times. Maintenance Interval Before operating the Multi-Cutter with Hedge Trimmer Attachment it is necessary to check the adjustment of the cutting blades. -
Page 32: Mc-Px/Ps/Pl (Pruner Attachment)
MC-PX/PS/PL (Pruner Attachment) Sharpening saw chain 30° Whenever wood chips become small and fine or the wood cannot be cut without pressing the pruner hard against it, then it may be necessary to sharpen the saw chain. 1. Tighten the saw chain slightly firmer than usual then se- cure the pruner’s main unit. - Page 33 Guide bar care 1. When work using the pruner is finished for the day, re- move the guide bar and saw chain from the pruner. 2. Remove any wood chips or other particles attached to the groove of the guide bar or in the oil hole. Be particularly certain that no particles are clogging the oil hole.
-
Page 34: Mc-T (Cultivator Attachment)
・ Always turn off your Multi-Cutter before you clean or perform any maintenance on it. The BUSHRANGER Multi-Cutter will provide maximum performance for many, many hours if it is main- tained properly. Good maintenance includes regular checking of all fasteners for correct tightness, and cleaning the entire machine. -
Page 35: Troubleshooting
・Throttle wire has come loose ・Tighten throttle wire Engine lacks power or stalls ・Dirty air filter ・Clean or replace air filter when cutting If further assistance is required, contact your local authorized BUSHRANGER service dealer. Specifications MT261 With MC-S MC-E MC-HT MC-HTS Weight, kg ※1... - Page 36 11 Sodium Street, Narangba Qld 4504 P/N.241567-00 GB 1808 IN...